Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

ISDN Setup

I'm setting up a new ISDN link. The link thous the NT Box shows the line as active does not come up. I have checked with local telco and they've confirmed the line as being OK. The show isdn status output is as follow:

003R#show isdn status

ISDN BRI3/1 interface

dsl 25, interface ISDN Switchtype = basic-net3

Layer 1 Status:

DEACTIVATED

Layer 2 Status:

Layer 2 NOT Activated

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 25 CCBs = 0

The Free Channel Mask: 0x80000003

Number of L2 Discards = 0, L2 Session ID = 44

A sample debug output is as follows:

Mar 11 09:36:58.602 UTC: ISDN BR3/1: Outgoing call id = 0x8025, dsl 25

Mar 11 09:36:58.606 UTC: ISDN BR3/1: Event: Call to 27118835714 at 64 Kb/s

Mar 11 09:36:58.606 UTC: ISDN BR3/1: process_bri_call(): call id 0x8025, called_number 27118835714, speed 64, call ty

e DATA

Mar 11 09:36:58.606 UTC: CCBRI_Go Fr Host InPkgInfo (Len=26) :

Mar 11 09:36:58.606 UTC: 1 19 1 80 25 0 4 2 88 90 18 1 83 2C B 32 37 31 31 38 38 33 35 37 31 34

Mar 11 09:36:58.606 UTC:

Mar 11 09:36:58.606 UTC: CC_CHAN_GetIdleChanbri: dsl 25

Mar 11 09:36:58.606 UTC: Found idle channel B1

Mar 11 09:36:58.614 UTC: ISDN BR3/1: Activating

Mar 11 09:36:58.614 UTC: ISDN BR3/1 EVENT: isdn_sw_cstate: State = 4, Old State = 4.

Mar 11 09:37:00.614 UTC: ISDN BR3/1: Could not bring up interface

Mar 11 09:37:00.614 UTC: ISDN BR3/1: Shutting down ISDN Layer 3

Mar 11 09:37:00.614 UTC: ISDN BR3/1: LIF_EVENT: ces/callid 1/0x8025 HOST_DISCONNECT_ACK

Mar 11 09:37:00.618 UTC: ISDN BR3/1: Error: Unfound B-channel on Disconnect_Ack - callid 0x8025

Mar 11 09:37:00.618 UTC: ISDN BR3/1: Activating .

Mar 11 09:37:02.602 UTC: ISDN BR3/1: Outgoing call id = 0x8026, dsl 25

Mar 11 09:37:02.602 UTC: ISDN BR3/1: Event: Call to 27118835714 at 64 Kb/s

Mar 11 09:37:02.602 UTC: ISDN BR3/1: process_bri_call(): call id 0x8026, called_number 27118835714, speed 64, call ty

The link does not come up in all the layers. The NT box has been tested with a different working ISDN line and found to be OK. I will appreciate anyone who can assist pick out whta the issue could be. The configuration of the Bri3/1 is follows:

interface BRI3/1

ip address 192.168.1.13 255.255.255.0

no ip address

encapsulation ppp

no ip split-horizon

no ip mroute-cache

dialer wait-for-carrier-time 80

dialer map ip 192.168.1.12 name BRANCH_RTR broadcast 27118835714

dialer hold-queue 20

dialer-group 1

isdn switch-type basic-net3

isdn tei-negotiation first-call

no cdp enable

ppp authentication chap

Thanks you

4 REPLIES
New Member

Re: ISDN Setup

Hi nickolas

first of pls check your router BRI card support the ISDN, Pls share the sh diag & sh ver report so that further can be check.

Regards

Pawan Rajput

New Member

Re: ISDN Setup

This is Sammy on behalf of Nicholas: The router has been used before to originate ISDN calls. Here's sh ver & sh diag:

003R#show ver

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-I-M), Version 12.2(7b), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Mon 04-Mar-02 20:23 by pwade

Image text-base: 0x600089A8, data-base: 0x60A6A000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

SCKE003R uptime is 1 week, 3 days, 22 hours, 23 minutes

System returned to ROM by power-on

System image file is "flash:c3640-i-mz.122-7b.bin"

cisco 3640 (R4700) processor (revision 0x00) with 45056K/4096K bytes of memory.

Processor board ID 27583135

R4700 CPU at 100Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

Basic Rate ISDN software, Version 1.1.

2 FastEthernet/IEEE 802.3 interface(s)

8 ISDN Basic Rate interface(s)

64 terminal line(s)

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

003R#show diag

Slot 1:

Async Port adapter, 32 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 0.1 Board revision H0

Serial number 28181831 Part number 800-02245-06

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 63 00 01 01 AE 05 47 50 08 C5 06 00 00 00 00

0x30: 88 00 00 00 02 05 07 00 FF FF FF FF FF FF FF FF

Slot 2:

Async Port adapter, 32 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 0.1 Board revision H0

Serial number 28182024 Part number 800-02245-06

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 63 00 01 01 AE 06 08 50 08 C5 06 00 00 00 00

0x30: 88 00 00 00 02 05 07 00 FF FF FF FF FF FF FF FF

Slot 3:

BRI (S/T) Port adapter, 8 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.0 Board revision E0

Serial number 28385664 Part number 800-01237-03

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 21 01 00 01 B1 21 80 50 04 D5 03 00 00 00 00

0x30: 70 00 00 00 02 05 30 17 FF FF FF FF FF FF FF FF

Silver

Re: ISDN Setup

Follow this link:

http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b78.shtml

Check your physical connectivity and router's interface U, S, T std.

- Dharmesh

Silver

Re: ISDN Setup

Hi ,

Check the volatage of the line using multimeter.

Place the multimeter points on Pin 4 and 5 and check whether u r getting a voltage between 96 to 104V on the isdn line.

If u r not getting the voltage then check with telco.

Tks,

satish

106
Views
0
Helpful
4
Replies
CreatePlease login to create content