Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

isdn test call - call rejecte

Hi networkers,

I have an ISDN line as a backup on our router. When I wanted to test it, I saw "call rejected" message:

TNRTEXCS02A1#debug isdn q931
debug isdn q931 is              ON.
TNRTEXCS02A1#
TNRTEXCS02A1#
TNRTEXCS02A1#isdn test call inter ser0/2/0:15 71979919
TNRTEXCS02A1#
*Jun 11 11:04:26.757 UTC: ISDN Se0/2/0:15 Q931: Sending SETUP  callref = 0x012D callID = 0x80AF switch = primary-net5 interface = User
*Jun 11 11:04:26.757 UTC: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8  callref = 0x012D
        Bearer Capability i = 0x8890
                Standard = CCITT
                Transfer Capability = Unrestricted Digital
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
        Called Party Number i = 0x81, '71979919'
                Plan:ISDN, Type:Unknown
*Jun 11 11:04:26.793 UTC: ISDN Se0/2/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x812D
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
*Jun 11 11:04:26.889 UTC: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8  callref = 0x01FD
        Sending Complete
        Bearer Capability i = 0x8890
                Standard = CCITT
                Transfer Capability = Unrestricted Digital
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98382
                Exclusive, Channel 2
        Calling Party Number i = 0x008
TNRTEXCS02A1#3, '71979919'
                Plan:Unknown, Type:Unknown
*Jun 11 11:04:26.893 UTC: ISDN Se0/2/0:15 Q931: Received SETUP  callref = 0x81FD callID = 0x01FE switch = primary-net5 interface = User
*Jun 11 11:04:26.893 UTC: ISDN Se0/2/0:1: Incoming call rejected, unbindable
*Jun 11 11:04:26.893 UTC: ISDN Se0/2/0:15 **ERROR**: call_incoming: DIALER ERROR 0x1: b channel 1 call id 0x1FE
*Jun 11 11:04:26.893 UTC: ISDN Se0/2/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x81FD
        Cause i = 0x8095 - Call rejected
*Jun 11 11:04:26.945 UTC: ISDN Se0/2/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x812D
        Cause i = 0x8095 - Call rejected
*Jun 11 11:04:26.945 UTC: ISDN Se0/2/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x012D
*Jun 11 11:04:26.961 UTC: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x812D
TNRTEXCS02A1#

Any help?

Everyone's tags (5)
5 REPLIES
Hall of Fame Super Gold

Re: isdn test call - call rejecte

Send "show diag" and "show conf".

New Member

Re: isdn test call - call rejecte

Hi,

Here they are

Hall of Fame Super Gold

Re: isdn test call - call rejecte

Alls seems good, you may need to bring this to the TAC.

New Member

Re: isdn test call - call rejected

Could it be because of the IOS? I have a 3925 chassis .

I attached the "show version" output if it helps

New Member

Re: isdn test call - call rejected

I found it. I removed the 'dialer remote-name" and it worked. I think it was an authentication issue because both PPP chap hostname and dialer remote-name were set under the dialer interface

4809
Views
7
Helpful
5
Replies