Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Line card installed in 6506-E in VSS mode

We are using 6506-E in VSS environment with following modules installed.

6506-E Modules

Mod Ports Card Type                             Model             Serial No.

--- ----- -------------------------------------- ------------------ -----------

1   4 CEF720 4 port 10-Gigabit Ethernet     WS-X6704-10GE     SAL14491P9Z

2   4 CEF720 4 port 10-Gigabit Ethernet     WS-X6704-10GE     SAL14491PBV

3   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL14480S7S

6   5 Supervisor Engine 720 10GE (Active)   VS-S720-10G       SAL1446ZS0N

Mod Sub-Module                 Model             Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

1  Centralized Forwarding Card WS-F6700-CFC       SAL1448172S 4.1   Ok

2 Centralized Forwarding Card WS-F6700-CFC       SAL144816Y1 4.1   Ok

3 Centralized Forwarding Card WS-F6700-CFC       SAL144814UE 4.1   Ok

6 Policy Feature Card 3       VS-F6K-PFC3C       SAL14470720 1.1   Ok

6 MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1446001V 5.1   Ok

Now we are running out of ports and have one pair of 6509-E which we planning to decommissioned soon, have two WS-X6748-GE-TX modules installed on it which we would like to move to our  6506-E pair.

6509-E modules:

Mod Ports Card Type                             Model             Serial No.

--- ----- -------------------------------------- ------------------ -----------

2   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL09169CTY

5   2 Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL09444784

6   2 Supervisor Engine 720 (Hot)           WS-SUP720-3B       SAL09433YXL

7   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL1128UB7B

8   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL1128U8VG

Mod Sub-Module                 Model             Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

2 Centralized Forwarding Card WS-F6700-CFC       SAL094447Y6 2.0   Ok

5 Policy Feature Card 3      WS-F6K-PFC3B       SAL09423FHA 2.1   Ok

5 MSFC3 Daughterboard         WS-SUP720         SAL09412T4C 2.3   Ok

6 Policy Feature Card 3       WS-F6K-PFC3B       SAL094449L3 2.1   Ok

6 MSFC3 Daughterboard         WS-SUP720         SAL09433YMY 2.3   Ok

7 Centralized Forwarding Card WS-F6700-CFC       SAD1128081W 3.1   Ok

8 Centralized Forwarding Card WS-F6700-CFC       SAD112807WW 3.1   Ok

My question is, if my 6506 SUP able take this line card without any issue and keep running in VSS mode, and do I have to do any changes in configuration? and which slot can I installed this card in?

sh ver

cisco WS-C6506-E (R7000) processor (revision 1.2) with 983008K/65536K bytes of memory.

Processor board ID XXXXXXXXXX

SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache

Last reset from s/w reset

1 Virtual Ethernet interface

102 Gigabit Ethernet interfaces

20 Ten Gigabit Ethernet interfaces

1917K bytes of non-volatile configuration memory.

8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).

Power:

system power total =     5771.64 Watts (137.42 Amps @ 42V)

system power used =     1690.92 Watts (40.26 Amps @ 42V)

system power available = 4080.72 Watts (97.16 Amps @ 42V)

Slot Card-Type         Watts   A @42V Watts   A @42V State State

---- ------------------ ------- ------ ------- ------ ----- -----

1   WS-X6704-10GE       295.26 7.03   295.26 7.03 on   on

2   WS-X6704-10GE       295.26 7.03   295.26 7.03 on   on

3   WS-X6748-GE-TX     325.50 7.75   325.50 7.75 on   on

5   (Redundant Sup)       -     -     338.10 8.05 -     -

6   VS-S720-10G         338.10 8.05   338.10 8.05 on   on

203
Views
0
Helpful
0
Replies
CreatePlease to create content