ā03-30-2012 03:41 AM - edited ā03-04-2019 03:51 PM
Hi
For 124 network i have given the local prefernce value as 300 but when i excuted the command value is not displaying ?
But 500 value is displaying .
route-map AIR, permit, sequence 10
Match clauses:
ip address prefix-lists: DEFAULT
Set clauses:
local-preference 300
Router-RSA#show ip bgp
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
* 0.0.0.0 124.x.x.x 0 0 9XXX i
*> 202.x.x.x 0 500 0 9XXX i
ā03-30-2012 03:47 AM
Hi,
could you post output of sh ip prefix
Regards.
Alain
ā03-30-2012 03:49 AM
Hi,
I understand you are talking about the default route, not 124 network?
Are you sure the prefix-lists DEFAULT is matching it?
And the route-map AIR is applied correctly?
If yes, have you tried
clear ip bgp * soft
on your router?
HTH,
Milan
ā03-30-2012 04:05 AM
ip prefix-list DEFAULT: 1 entries
seq 5 permit 0.0.0.0/0
ā03-30-2012 04:24 AM
Hi,
Do post your config excluding sensitive info for us to conclude
Regards,
Rustom Billimoria
CCIE R&S# 24798
Sent from my BlackBerryĀ® smartphone from Tata Indicom
ā04-02-2012 02:51 AM
Hi
I have even excuted the command clear ip bgp still local prefernce is not displaying for 300.
Router-RSA#show route-map
route-map DEFAULT-SCY-SIF, permit, sequence 10
Match clauses:
ip address prefix-lists: DEFAULT
Set clauses:
local-preference 400
Policy routing matches: 0 packets, 0 bytes
route-map DEFAULT-PRY-SIF, permit, sequence 10
Match clauses:
ip address prefix-lists: DEFAULT
Set clauses:
local-preference 500
Policy routing matches: 0 packets, 0 bytes
route-map AIR-IN, permit, sequence 10
Match clauses:
ip address prefix-lists: DEFAULT
Set clauses:
local-preference 300
Policy routing matches: 0 packets, 0 bytes
route-map AIR-OUT, permit, sequence 10
Match clauses:
ip address prefix-lists: AIR-OUT
Set clauses:
Policy routing matches: 0 packets, 0 bytes
route-map SIF-OUT, permit, sequence 10
Match clauses:
ip address prefix-lists: SIF-OUT
Set clauses:
Policy routing matches: 0 packets, 0 bytes
ip prefix-list AIR-OUT seq 5 permit 202.x.x.x/24
!
ip prefix-list DEFAULT seq 5 permit 0.0.0.0/0
!
!
ip prefix-list SIF-OUT seq 5 permit 202.x.x.x/24
ā04-02-2012 03:19 AM
Hi,
it seems route-map DEFAULT-PRY-SIF is applied on the default route prefix received, not route-map AIR-IN.
Can you paste the config part where you are applying the route maps?
HTH,
Milan
ā04-02-2012 11:10 PM
yA route-map DEFAULT-PRY-SIF is applied on the default route prefix BUT WHEN ever SIF goes down .route-map AIR-IN
will be used .so when i excute show ip bgp when SIF goes down local prefernce value for AIR is not displayed.
ā04-03-2012 01:16 AM
Hi,
I believe the route-map AIR-IN might not be applied for some reason.
Otherwise you should see LP 300 in ypur original output.
HTH,
Milan
ā04-03-2012 04:08 AM
Hi
It is applied when i shutdown interface to which SIF is applied than traffic is going through AIR_IN routemap
ā04-03-2012 06:21 AM
Hi Milan,
I reconfigured the bgp and clear ip bgp now it is working fine.
Thank Milan fot u help
ā03-30-2012 04:49 AM
Hi Prashant,
Do you have any other route-map entry with lower seq number which already matches the default route?
Did you apply the route map to the other neigbor (124.x.x.x) to in direction?
Did you try clear ip bgp with this neigbor?
Hope that helps,
Vasilis
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: