Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

lost cell delineation

Hello all,

I'm using a cisco 2811 IOS c2800nm-entservicesk9-mz.124-5.bin with 4 VWIC-2MFT-E1 modules connected with eight E1 atm link configured with 2 ima groups.

Even if i've replaced wic and cables i continue to receive these error:

*Aug 29 13:50:19.614: %ATM_AIM-5-CELL_ALARM_UP: Interface ATM0/2/0 lost cell delineation.

*Aug 29 13:50:19.630: %ATM_AIM-5-CELL_ALARM_DOWN: Interface ATM0/2/0 regained cell delineation.

*Aug 29 13:50:20.130: %ATM_AIM-5-ACTIVE_LINK_DOWN: Interface ATM0/2/0 of IMA Group ATM0/IMA1 is now inactive.

*Aug 29 13:50:20.130: %ATM_AIM-5-ACTIVE_LINK_CHANGE: IMA Group ATM0/IMA1 now has 3 active links.

*Aug 29 13:50:20.158: %ATM_AIM-5-ACTIVE_LINK_UP: Interface ATM0/2/0 of IMA Group ATM0/IMA1 is now active.

and for all the interface grouped to the same ima group.

here the configuration:

network-clock-participate wic 0

network-clock-participate wic 1

network-clock-participate wic 2

network-clock-participate wic 3

network-clock-participate aim 0

network-clock-participate aim 1

network-clock-select 1 E1 0/0/0

network-clock-select 2 E1 0/0/1

network-clock-select 3 E1 0/2/0

network-clock-select 4 E1 0/3/0

...

controller E1 0/0/0

mode atm aim 0

!

controller E1 0/0/1

mode atm aim 0

!

controller E1 0/1/0

mode atm aim 0

!

controller E1 0/1/1

mode atm aim 0

!

controller E1 0/2/0

mode atm aim 1

!

controller E1 0/2/1

mode atm aim 1

!

controller E1 0/3/0

mode atm aim 1

!

controller E1 0/3/1

mode atm aim 1

interface ATM0/IMA0

no ip address

load-interval 30

ima clock-mode common 0

no atm oversubscribe

no atm ilmi-keepalive

service-policy output VOICE-POLICY

!

interface ATM0/IMA0.1 point-to-point

description WORKING

ip address 192.168.1.6 255.255.255.252

ip mtu 1500

ip load-sharing per-packet

no snmp trap link-status

pvc 11/100

protocol ip 192.168.1.5 broadcast

ubr 7680

oam-pvc manage

encapsulation aal5snap

!

!

interface ATM0/IMA1

no ip address

load-interval 30

ima clock-mode common 0

no atm oversubscribe

no atm ilmi-keepalive

service-policy output VOICE-POLICY

!

interface ATM0/IMA1.1 point-to-point

description NOT WORKING

ip address 192.168.1.2 255.255.255.252

ip mtu 1500

ip load-sharing per-packet

no snmp trap link-status

pvc 11/100

protocol ip 192.168.1.1 broadcast

ubr 7680

oam-pvc manage

encapsulation aal5snap

!

!

interface ATM0/0/0

no ip address

scrambling-payload

ima-group 0

no atm oversubscribe

no atm ilmi-keepalive

!

interface ATM0/0/1

no ip address

scrambling-payload

ima-group 0

no atm oversubscribe

no atm ilmi-keepalive

!

interface ATM0/1/0

no ip address

scrambling-payload

ima-group 0

no atm oversubscribe

no atm ilmi-keepalive

!

interface ATM0/1/1

no ip address

scrambling-payload

ima-group 0

no atm oversubscribe

no atm ilmi-keepalive

!

interface ATM0/2/0

no ip address

scrambling-payload

ima-group 1

no atm oversubscribe

no atm ilmi-keepalive

!

interface ATM0/2/1

no ip address

scrambling-payload

ima-group 1

no atm oversubscribe

no atm ilmi-keepalive

!

interface ATM0/3/0

no ip address

scrambling-payload

ima-group 1

no atm oversubscribe

no atm ilmi-keepalive

!

interface ATM0/3/1

no ip address

scrambling-payload

ima-group 1

no atm oversubscribe

no atm ilmi-keepalive

These two links are provided by the local incumbent but i don't know if they are attached to the same device;

If the two links are connected to a different device, is it possible that the second link use le clock of

the first one losing delineation?

Thanks in advance

1 REPLY
Silver

Re: lost cell delineation

See as of error's mean: %ATM_AIM-5-CELL_ALARM_UP: Interface ATM0/2/0 lost cell delineation.

If the alarm or the interface is flapping, check the clocking configuration.

PLEAE CHECK YOUR CKOCK CONFIGURATION. NO ACTION REQUIRED ON Interface ATM0/2/0 regained cell delineation.

http://www.cisco.com/en/US/products/ps6350/products_system_message_guide_chapter09186a0080462670.html

Regards,

Dharmesh Purohit

3044
Views
0
Helpful
1
Replies