Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

MGX - VISM AAL1 switching configurations.

Hi Friends,

I have a setup of two Analog PBXs' and two MGX. I have connected the two PBXs' to the VISM. The setup looks like this..

PBX1 -------- VISM1 --------- VISM2 ------------ PBX2

I want to configure AAL1 switching between two VISMs'.

could anybody provide me with a sample configurations for how to go about it.

1 ACCEPTED SOLUTION

Accepted Solutions
Community Member

Re: MGX - VISM AAL1 switching configurations.

hello,

I have here AAL2 sample config.

=====================================

using VISM1 line 1: as slave end


addln 1        
cnfln 1 2 10 2 1 1   
cnflnsig 1 1       
addendpts 1 1 1 24 

bearer:
addcon  139 1 2 2 1000 2 4 650 6500
        Connection ID:

addcid 1 139 8 4 1 7 1 250 1 1 1 1 2 10
addcid 2 139 9 4 1 7 1 250 1 1 1 1 2 10
addcid 3 139 10 4 1 7 1 250 1 1 1 1 2 10
addcid 4 139 11 4 1 7 1 250 1 1 1 1 2 10
addcid 5 139 12 4 1 7 1 250 1 1 1 1 2 10
addcid 6 139 13 4 1 7 1 250 1 1 1 1 2 10
addcid 7 139 14 4 1 7 1 250 1 1 1 1 2 10
addcid 8 139 15 4 1 7 1 250 1 1 1 1 2 10
addcid 9 139 16 4 1 7 1 250 1 1 1 1 2 10
addcid 10 139 17 4 1 7 1 250 1 1 1 1 2 10
addcid 11 139 18 4 1 7 1 250 1 1 1 1 2 10
addcid 12 139 19 4 1 7 1 250 1 1 1 1 2 10
addcid 13 139 20 4 1 7 1 250 1 1 1 1 2 10
addcid 14 139 21 4 1 7 1 250 1 1 1 1 2 10
addcid 15 139 22 4 1 7 1 250 1 1 1 1 2 10
addcid 16 139 23 4 1 7 1 250 1 1 1 1 2 10
addcid 17 139 24 4 1 7 1 250 1 1 1 1 2 10
addcid 18 139 25 4 1 7 1 250 1 1 1 1 2 10
addcid 19 139 26 4 1 7 1 250 1 1 1 1 2 10
addcid 20 139 27 4 1 7 1 250 1 1 1 1 2 10
addcid 21 139 28 4 1 7 1 250 1 1 1 1 2 10
addcid 22 139 29 4 1 7 1 250 1 1 1 1 2 10
addcid 23 139 30 4 1 7 1 250 1 1 1 1 2 10
addcid 24 139 31 4 1 7 1 250 1 1 1 1 2 10

=====================================

using VISM2 line 1: as master end


addln 1        
cnfln 1 2 10 2 1 1   
cnflnsig 1 1       
addendpts 1 1 1 24 

bearer:
addcon  139 1 2 2 1000 1   4 650 6500

note: Copy the Conn ID generated on the slave side:
        
addcid 1 139 8 4 1 7 1 250 1 1 1 1 2 10
addcid 2 139 9 4 1 7 1 250 1 1 1 1 2 10
addcid 3 139 10 4 1 7 1 250 1 1 1 1 2 10
addcid 4 139 11 4 1 7 1 250 1 1 1 1 2 10
addcid 5 139 12 4 1 7 1 250 1 1 1 1 2 10
addcid 6 139 13 4 1 7 1 250 1 1 1 1 2 10
addcid 7 139 14 4 1 7 1 250 1 1 1 1 2 10
addcid 8 139 15 4 1 7 1 250 1 1 1 1 2 10
addcid 9 139 16 4 1 7 1 250 1 1 1 1 2 10
addcid 10 139 17 4 1 7 1 250 1 1 1 1 2 10
addcid 11 139 18 4 1 7 1 250 1 1 1 1 2 10
addcid 12 139 19 4 1 7 1 250 1 1 1 1 2 10
addcid 13 139 20 4 1 7 1 250 1 1 1 1 2 10
addcid 14 139 21 4 1 7 1 250 1 1 1 1 2 10
addcid 15 139 22 4 1 7 1 250 1 1 1 1 2 10
addcid 16 139 23 4 1 7 1 250 1 1 1 1 2 10
addcid 17 139 24 4 1 7 1 250 1 1 1 1 2 10
addcid 18 139 25 4 1 7 1 250 1 1 1 1 2 10
addcid 19 139 26 4 1 7 1 250 1 1 1 1 2 10
addcid 20 139 27 4 1 7 1 250 1 1 1 1 2 10
addcid 21 139 28 4 1 7 1 250 1 1 1 1 2 10
addcid 22 139 29 4 1 7 1 250 1 1 1 1 2 10
addcid 23 139 30 4 1 7 1 250 1 1 1 1 2 10
addcid 24 139 31 4 1 7 1 250 1 1 1 1 2 10

1 REPLY
Community Member

Re: MGX - VISM AAL1 switching configurations.

hello,

I have here AAL2 sample config.

=====================================

using VISM1 line 1: as slave end


addln 1        
cnfln 1 2 10 2 1 1   
cnflnsig 1 1       
addendpts 1 1 1 24 

bearer:
addcon  139 1 2 2 1000 2 4 650 6500
        Connection ID:

addcid 1 139 8 4 1 7 1 250 1 1 1 1 2 10
addcid 2 139 9 4 1 7 1 250 1 1 1 1 2 10
addcid 3 139 10 4 1 7 1 250 1 1 1 1 2 10
addcid 4 139 11 4 1 7 1 250 1 1 1 1 2 10
addcid 5 139 12 4 1 7 1 250 1 1 1 1 2 10
addcid 6 139 13 4 1 7 1 250 1 1 1 1 2 10
addcid 7 139 14 4 1 7 1 250 1 1 1 1 2 10
addcid 8 139 15 4 1 7 1 250 1 1 1 1 2 10
addcid 9 139 16 4 1 7 1 250 1 1 1 1 2 10
addcid 10 139 17 4 1 7 1 250 1 1 1 1 2 10
addcid 11 139 18 4 1 7 1 250 1 1 1 1 2 10
addcid 12 139 19 4 1 7 1 250 1 1 1 1 2 10
addcid 13 139 20 4 1 7 1 250 1 1 1 1 2 10
addcid 14 139 21 4 1 7 1 250 1 1 1 1 2 10
addcid 15 139 22 4 1 7 1 250 1 1 1 1 2 10
addcid 16 139 23 4 1 7 1 250 1 1 1 1 2 10
addcid 17 139 24 4 1 7 1 250 1 1 1 1 2 10
addcid 18 139 25 4 1 7 1 250 1 1 1 1 2 10
addcid 19 139 26 4 1 7 1 250 1 1 1 1 2 10
addcid 20 139 27 4 1 7 1 250 1 1 1 1 2 10
addcid 21 139 28 4 1 7 1 250 1 1 1 1 2 10
addcid 22 139 29 4 1 7 1 250 1 1 1 1 2 10
addcid 23 139 30 4 1 7 1 250 1 1 1 1 2 10
addcid 24 139 31 4 1 7 1 250 1 1 1 1 2 10

=====================================

using VISM2 line 1: as master end


addln 1        
cnfln 1 2 10 2 1 1   
cnflnsig 1 1       
addendpts 1 1 1 24 

bearer:
addcon  139 1 2 2 1000 1   4 650 6500

note: Copy the Conn ID generated on the slave side:
        
addcid 1 139 8 4 1 7 1 250 1 1 1 1 2 10
addcid 2 139 9 4 1 7 1 250 1 1 1 1 2 10
addcid 3 139 10 4 1 7 1 250 1 1 1 1 2 10
addcid 4 139 11 4 1 7 1 250 1 1 1 1 2 10
addcid 5 139 12 4 1 7 1 250 1 1 1 1 2 10
addcid 6 139 13 4 1 7 1 250 1 1 1 1 2 10
addcid 7 139 14 4 1 7 1 250 1 1 1 1 2 10
addcid 8 139 15 4 1 7 1 250 1 1 1 1 2 10
addcid 9 139 16 4 1 7 1 250 1 1 1 1 2 10
addcid 10 139 17 4 1 7 1 250 1 1 1 1 2 10
addcid 11 139 18 4 1 7 1 250 1 1 1 1 2 10
addcid 12 139 19 4 1 7 1 250 1 1 1 1 2 10
addcid 13 139 20 4 1 7 1 250 1 1 1 1 2 10
addcid 14 139 21 4 1 7 1 250 1 1 1 1 2 10
addcid 15 139 22 4 1 7 1 250 1 1 1 1 2 10
addcid 16 139 23 4 1 7 1 250 1 1 1 1 2 10
addcid 17 139 24 4 1 7 1 250 1 1 1 1 2 10
addcid 18 139 25 4 1 7 1 250 1 1 1 1 2 10
addcid 19 139 26 4 1 7 1 250 1 1 1 1 2 10
addcid 20 139 27 4 1 7 1 250 1 1 1 1 2 10
addcid 21 139 28 4 1 7 1 250 1 1 1 1 2 10
addcid 22 139 29 4 1 7 1 250 1 1 1 1 2 10
addcid 23 139 30 4 1 7 1 250 1 1 1 1 2 10
addcid 24 139 31 4 1 7 1 250 1 1 1 1 2 10

213
Views
0
Helpful
1
Replies
CreatePlease to create content