Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Multicast on 4507 issue

We have several 4507s deployed running

12.2(46)SG Enterprise Services

I am ablel to issue the ip multicast-routing command with no issues, but when I go to enable Multicast on an SVI the

ip pim option is not there. Any ideas on this?

3 REPLIES
Bronze

Re: Multicast on 4507 issue

What supervisors are you running. I have two 4506's with sup 4's and I have pim.

4506-A#sh ver

Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M),

Version 12.2(46)SG, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Fri 27-Jun-08 16:24 by prod_rel_team

Image text-base: 0x10000000, data-base: 0x11E3C0D8

ROM: 12.1(20r)EW1

Dagobah Revision 95, Swamp Revision 29

4506-A uptime is 4 days, 16 hours, 40 minutes

System returned to ROM by power-on

System image file is "bootflash:"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco WS-C4506 (MPC8245) processor (revision 7) with 524288K bytes of memory.

Processor board ID FOX073803XX

MPC8245 CPU at 333Mhz, Supervisor IV

Last reset from PowerUp

20 Virtual Ethernet interfaces

96 FastEthernet interfaces

8 Gigabit Ethernet interfaces

403K bytes of non-volatile configuration memory.

Configuration register is 0x2101

4506-A#conf t

Enter configuration commands, one per line. End with CNTL/Z.

4506-A(config)#int vlan 206

4506-A(config-if)#ip pim sparse-mode

4506-A(config-if)#

New Member

Re: Multicast on 4507 issue

SUP IV's

Prichard-4507#sho ver

Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICES-M), Version 12.2(46)SG, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Fri 27-Jun-08 17:28 by prod_rel_team

Image text-base: 0x10000000, data-base: 0x11CE63D8

ROM: 12.1(20r)EW1

Dagobah Revision 95, Swamp Revision 29

Prichard-4507 uptime is 24 weeks, 2 days, 15 hours, 30 minutes

Uptime for this control processor is 1 week, 6 days, 18 hours, 58 minutes

System returned to ROM by power-on

System restarted at 22:09:39 cdt Mon Oct 6 2008

System image file is "bootflash:cat4500-entservices-mz.122-46.SG.bin"

cisco WS-C4507R (MPC8245) processor (revision 7) with 524288K bytes of memory.

Processor board ID FOX084001T4

MPC8245 CPU at 333Mhz, Supervisor IV

Last reset from PowerUp

8 Virtual Ethernet interfaces

100 Gigabit Ethernet interfaces

403K bytes of non-volatile configuration memory.

Configuration register is 0x2102

New Member

Re: Multicast on 4507 issue

Prichard-4507(config)#int vlan 158

Prichard-4507(config-if)#ip ?

Interface IP configuration subcommands:

access-group Specify access control for packets

address Set the IP address of an interface

admission Apply Network Admission Control

authentication authentication subcommands

bandwidth-percent Set EIGRP bandwidth limit

bgp BGP interface commands

broadcast-address Set the broadcast address of an interface

cef Cisco Express Forwarding interface commands

cgmp Enable/disable CGMP

dhcp Configure DHCP parameters for this interface

directed-broadcast Enable forwarding of directed broadcasts

dvmrp DVMRP interface commands

hello-interval Configures EIGRP-IPv4 hello interval

helper-address Specify a destination address for UDP broadcasts

hold-time Configures EIGRP-IPv4 hold time

igmp IGMP interface commands

information-reply Enable sending ICMP Information Reply messages

irdp ICMP Router Discovery Protocol

load-sharing Style of load sharing

local-proxy-arp Enable local-proxy ARP

mask-reply Enable sending ICMP Mask Reply messages

mrm Configure IP Multicast Routing Monitor tester

mroute-cache Enable switching cache for incoming multicast packets

mtu Set IP Maximum Transmission Unit

multicast IP multicast interface commands

next-hop-self Configures EIGRP-IPv4 next-hop-self

nhrp NHRP interface subcommands

ospf OSPF interface commands

pgm PGM Reliable Transport Protocol

policy Enable policy routing

probe Enable HP Probe support

proxy-arp Enable proxy ARP

rarp-server Enable RARP server for static arp entries

redirects Enable sending ICMP Redirect messages

rgmp Enable/disable RGMP

rip Router Information Protocol

route-cache Enable fast-switching cache for outgoing packets

router IP router interface commands

sap Session Advertisement Protocol interface commands

security DDN IP Security Option

split-horizon Perform split horizon

sticky-arp Allow the creation of sticky ARP entries

summary-address Perform address summarization

tcp TCP interface commands

unnumbered Enable IP processing without an explicit address

unreachables Enable sending ICMP Unreachable messages

vrf VPN Routing/Forwarding parameters on the interface

wccp WCCP interface commands

500
Views
0
Helpful
3
Replies
CreatePlease to create content