Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Multilink problem between cisco and Nortel router

Sir,

I have done multilink between cisco and nortel router.Its working fine.Some times multilink is up but not passing packets.If i give shutdown and no shutdown to multilink found packets are passing.

1.Any additional commands are there to multilink cisco and nortel router.What may be the problem.

Regards,

Senthil

7 REPLIES
Hall of Fame Super Silver

Re: Multilink problem between cisco and Nortel router

Hello Senthil,

this adds information to your previous thread.

PPP multilink is a standard so it should work and no special commands should be given to improve the behaviour

what is the PPP state in sh ppp multilink when user traffic doe not pass over it ?

the shut/ no shut resets the PPP state machine.

Hope to help

Giuseppe

New Member

Re: Multilink problem between cisco and Nortel router

Dear sir,

Output of Show ppp multilink while multilink up but not pinging is\

Multilink2, bundle name is ROUTER

  Bundle up for 20:58:58

  Bundle is Distributed

  0 lost fragments, 1686 reordered, 0 unassigned

  0 discarded, 0 lost received, 1/255 load

  0xBB2A4 received sequence, 0x64C109 sent sequence

  Member links: 16 active, 0 inactive (max not set, min not set)

    Se1/1/0/1:0, since 11:08:36, no frags rcvd

    Se1/1/0/2:0, since 11:08:36, no frags rcvd

    Se1/1/0/3:0, since 11:08:36, no frags rcvd

    Se1/1/0/4:0, since 11:08:36, no frags rcvd

   Se1/1/0/5:0, since 11:08:36, no frags rcvd

    Se1/1/0/6:0, since 11:08:36, no frags rcvd

    Se1/1/0/7:0, since 11:08:36, no frags rcvd

    Se1/1/0/8:0, since 11:08:36, no frags rcvd

    Se1/1/0/9:0, since 11:08:36, no frags rcvd

    Se1/1/0/10:0, since 11:08:36, no frags rcvd

    Se1/1/0/11:0, since 11:08:36, no frags rcvd

    Se1/1/0/12:0, since 11:08:36, no frags rcvd

    Se1/1/0/13:0, since 11:08:36, no frags rcvd

    Se1/1/0/14:0, since 11:08:36, no frags rcvd

    Se1/1/0/15:0, since 11:08:36, no frags rcvd

    Se1/1/0/16:0, since 11:08:36, no frags rcvd

Thanks and Regards,

senthil

New Member

Re: Multilink problem between cisco and Nortel router

Sir,SH ppp multilink output of another multilink

Multilink1, bundle name is RTR

  Bundle up for 4d12h

  22 lost fragments, 1183131 reordered, 0 unassigned

  5 discarded, 7 lost received, 1/255 load

  0x4ACD received sequence, 0x282B09 sent sequence

  Member links: 2 active, 0 inactive (max not set, min not set)

    Serial5/1:0, since 00:15:47, last rcvd seq 004ACC

    Serial3/3:0, since 05:43:23, last rcvd seq 004ACB.

Thanks and Regards,

Senthil

New Member

Re: Multilink problem between cisco and Nortel router

Kumar, make sure UDP traffic is enable on Nortel router. Some of the nortel routers don't handle UDP multilink traffic well. Look into pim or igmp forwarding solutions for your Nortel router.

Thx,

Eric

New Member

Re: Multilink problem between cisco and Nortel router

Sir,i am not expert in nortel router.how to check udp is enabled .

Thanks and Regards,

Senthil

New Member

Re: Multilink problem between cisco and Nortel router

please provide your Nortel Router model and current version.

Thx,

Eric

New Member

Re: Multilink problem between cisco and Nortel router

Sir,

Nortel secure 3120 router.

OPAL SW VERSION:        r9.2

Thanks and Regards,

Senthil

424
Views
0
Helpful
7
Replies
CreatePlease to create content