Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

NM-2CE1U and WIC-1T connecting problem

Dear All:

       Our company has a Cisco 3600 with NM-2CE1U,and Cisco 2600 with WIC-1T.There is a connecting problem below:

1.Serial2/1:1 is reset, line protocol is down

2.E1 2/1 is down

How do I slove these two problems?

3600#show interfaces serial 2/1:1

Serial2/1:1 is reset, line protocol is down
  Hardware is DSX1
  Description: connect to hualilu  with Yingtong 2M
  Internet address is 10.18.252.25/30
  MTU 1500 bytes, BW 1984 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation HDLC, loopback not set
  Keepalive set (10 sec)
  Last input 00:02:24, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/4636/0 (size/max/drops/flushes); Total output drops: 7910
  Queueing strategy: weighted fair
  Output queue: 0/1000/64/0 (size/max total/threshold/drops)
     Conversations  0/0/256 (active/max active/max total)
     Reserved Conversations 0/0 (allocated/max allocated)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     831 packets input, 19944 bytes, 0 no buffer
     Received 831 broadcasts, 0 runts, 0 giants, 0 throttles
     4636 input errors, 3818 CRC, 818 frame, 0 overrun, 0 ignored, 77 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 1978 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
  Timeslot(s) Used:1-31, Transmitter delay is 0 flags

3600#show controllers e1 2/1

E1 2/1 is down.
  Applique type is Channelized E1 - unbalanced
  Transmitter is sending remote alarm.
  Receiver has loss of frame.
  Framing is CRC4, Line Code is HDB3, Clock Source is Line.
  Data in current interval (452 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 452 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 452 Unavail Secs
  Total Data (last 24 hours)
     1634 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 86400 Fr Loss Secs, 5 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 5 Severely Err Secs, 86395 Unavail Secs

1 REPLY
Cisco Employee

Re: NM-2CE1U and WIC-1T connecting problem

Hello,

The controller is down due to an LOF (Loss of Frame).

Can you provide some details on the topology ?

Is there an external csu/dsu that is connecting to the WIC-1T ? If yes, how is it configured ?

On the NM, you have the following settings -

  Framing is CRC4, Line Code is HDB3, Clock Source is Line.

What are the settings you have on the CSU/DSU that is connecting to the WIC-1T ?

-Arun

327
Views
0
Helpful
1
Replies