Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

NMHDV2 modules on cisco 2811 chassis but the voice-ports are not showing up

What we are doing is that we are using NMHDV2 modules on cisco 2811 chassis but the voice-ports are not showing up for configuration. IOS that we are using is

"c2800nm-spservicesk9-mz.124-15.T9"

E/M signalling is being used on the voice ports.

Please advise on the below queries:

1) By default NMHDV2 has DSP resources available or not ?

2)If yes then as per my understanding they should be shown using sh voice dsp command, but in our case its not showing, is their any other command to check the PVDM/DSP availaibility.

3)Also how can we make the voice-ports available for configuration if DSP

resources is not the problem?

4)If their is problem with the NMHDV2 module then what card shall we order to solve this problem.

Below is the relevant output from the sh diag commang:

WIC Slot 3:

2nd generation - E&M Voice daughter card (2 port)

Hardware Revision : 5.1

Top Assy. Part Number : 800-23669-03

Board Revision : B0

Deviation Number : 0-0

Fab Version : 05

PCB Serial Number : FOC13233KEC

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Version Identifier : V01

Product (FRU) Number : VIC2-2E/M

CLEI Code : COUIAC2CAA

WIC Slot 0:

VG - E&M Voice daughter card (2 port)

Hardware Revision : 5.1

Top Assy. Part Number : 800-23669-03

Board Revision : B0

Deviation Number : 0-0

Fab Version : 05

PCB Serial Number : FOC13233KJG

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Version Identifier : V01

Product (FRU) Number : VIC2-2E/M

CLEI Code : COUIAC2CAA

  • WAN Routing and Switching
5 REPLIES
Hall of Fame Super Silver

Re: NMHDV2 modules on cisco 2811 chassis but the voice-ports are

Hello Rahul,

you can see if any DSP are present looking at the whole output of

show diag

if the DSP are missing you cannot use the voice ports.

Hope to help

Giuseppe

New Member

Re: NMHDV2 modules on cisco 2811 chassis but the voice-ports are

Hello Giuseppe ,

Thanks for the update. Can we order these DSP's in separate, or is there anyway we can work out this problem of our's.

I am attaching full output of sh diag and sh invntory and sh version command.

Hall of Fame Super Silver

Re: NMHDV2 modules on cisco 2811 chassis but the voice-ports are

Hello Rahul,

yes there are part numbers for DSP.

the types you can insall on your card should be:

1 to 4 of:

PVDM2-8 (½ DSP)

PVDM2-16 (1 DSP)

PVDM2-32 (2 DSPs)

PVDM2-48 (3 DSPs)

PVDM2-64 (4 DSPs)

Edit:

interesting sh inventory shows no modules are installed

NAME: "High Density Voice2 Network module with no board interface on Slot 1", DESCR: >>"High Density Voice2 Network module with no board interface "

PID: NM-HDV2 , VID: V02 , SN: FOC13261QLF

Hope to help

Giuseppe

New Member

Re: NMHDV2 modules on cisco 2811 chassis but the voice-ports are

Hello Giuseppe,

Can u please elaborate on below :

interesting sh inventory shows no modules are installed

NAME: "High Density Voice2 Network module with no board interface on Slot 1", DESCR: >>"High Density Voice2 Network module with no board interface "

PID: NM-HDV2 , VID: V02 , SN: FOC13261QLF

Hall of Fame Super Silver

Re: NMHDV2 modules on cisco 2811 chassis but the voice-ports are

Hello Rahul,

nothing important it was just a comment on the fact that the message can be seen as a sign of no PVDM2 on the card.

These second generation voice cards can mount up to 4 PVDM2 on subslots

Hope to help

Giuseppe

995
Views
4
Helpful
5
Replies