Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

No output on show run

We have an issue with our 7200. We can't output the show run, wr term, other show command works. Is there a way to resolve this?

thanks

spdum1edmz2r01#show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-IS-M), Version 12.0(7)XE1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC:Home:SW:IOS:Specials for info

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Fri 04-Feb-00 21:31 by lstringr

Image text-base: 0x60008900, data-base: 0x60FF4000

ROM: System Bootstrap, Version 11.1(13)CA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

BOOTFLASH: 7200 Software (C7200-BOOT-M), Version 12.0(10)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

spdum1edmz2r01 uptime is 11 weeks, 5 days, 5 hours, 30 minutes

System returned to ROM by reload at 21:16:29 BRA Thu Mar 29 2007

System restarted at 21:18:06 BRA Thu Mar 29 2007

System image file is "slot0:c7200-is-mz.120-7.XE1"

cisco 7206 (NPE200) processor with 57344K/8192K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

6 slot midplane, Version 1.3

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

24 Ethernet/IEEE 802.3 interface(s)

2 FastEthernet/IEEE 802.3 interface(s)

125K bytes of non-volatile configuration memory.

4096K bytes of packet SRAM memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

4096K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x102

spdum1edmz2r01#show rim

spdum1edmz2r01#show run

spdum1edmz2r01#show running-config

spdum1edmz2r01#dir nv

spdum1edmz2r01#dir nvram:

Directory of nvram:/

1 -rw- 53202 <no date> startup-config

2 ---- 26 <no date> private-config

3 -rw- 53202 <no date> underlying-config

129016 bytes total (75814 bytes free)

spdum1edmz2r01#dir /all flaa

spdum1edmz2r01#dir /all fla

spdum1edmz2r01#dir /all flash:

Directory of slot0:/

1 -rw- 9239932 Jun 22 2000 23:01:07 c7200-is-mz.120-7.XE1

2 -rw- 273384 Dec 07 2002 23:30:52 config

20578304 bytes total (11064732 bytes free)

spdum1edmz2r01#

1 REPLY

Re: No output on show run

HI, [Pls Rate if Helps]

Error in: Configuration Register Setting...

Your COnfiguration Register set is: 0x102

Set your Configuration Register Value to:

"Configuration register is 0x2102"

INFO: On power-up or reload, this router will load the IOS image stored in flash-RAM

(assuming one exists). If no valid IOS image or flash-RAM exists, this router will attempt to boot in order of following methods:

- boot system commands

- a TFTP-server (using a default IOS image filename)

INFO: On power-up or reload, this router will load it's configuration from a file

stored in NVRAM.

WARNING: On power-up or reload, if an error occurs with it's prescribed IOS boot method(s), this router will not boot into the fall-back (reduced) IOS image stored on ROM (sometimes called ROM-boot or boot-strap mode)

TRY THIS: To restore the router's fall-back ROM-boot to default function, enter

configuration mode and reset the configuration register with the 'config-register' command. Set the 13th low-order bit (from the right) of the register to binary 0. (You'll have to convert the final register value from binary to hexadecimal

0xABCD) for the 'config-register' command.)

PLS RATE if HELPS

Best Regards,

Guru Prasad R

107
Views
5
Helpful
1
Replies