Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

ospf on 3550 vs 4500

Im having the following command on a switch 3550, but when I try now migrating it over to 4500, I cannot get the same command in, can you help me?

router ospf 109

log-adjacency-changes

network 10.56.1.0 0.0.0.255 area 0.0.0.0

!

6 REPLIES
Hall of Fame Super Blue

Re: ospf on 3550 vs 4500

Hi Jorge

Which bit of the config won't go in, all of it ?

What error message are you getting ?

Which IOS version are you running on the 4500 ?

Jon

Community Member

Re: ospf on 3550 vs 4500

Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12

.2(25)EWA10, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 11-Jul-07 00:08 by dchih

Image text-base: 0x10000000, data-base: 0x114BC038

ROM: 12.2(31r)SG3

Pod Revision 14, Force Revision 34, Tie Revision 32

ITC0004 uptime is 3 hours, 30 minutes

Uptime for this control processor is 3 hours, 30 minutes

System returned to ROM by Stateful Switchover

System restarted at 12:09:46 cet Sat Dec 8 2007

System image file is "bootflash:cat4000-i9s-mz.122-25.EWA10.bin"

cisco WS-C4510R (MPC8540) processor (revision 11) with 524288K bytes of memory.

Processor board ID FOX11140THS

MPC8540 CPU at 800Mhz, Supervisor V-10GE

Last reset from PowerUp

15 Virtual Ethernet interfaces

296 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.

Configuration register is 0x2102

Hall of Fame Super Bronze

Re: ospf on 3550 vs 4500

You have a basic L3 image. For OSPF support, you need the enhanced L3 image cat4000-i5s-mz.122-25.EWA10.bin

Community Member

Re: ospf on 3550 vs 4500

You are right, I didn't upgraded it has I tought.

now should be ok, but how do I configure OSP?

ITC0004#sh ver

Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I5S-M), Version 12

.2(25)EWA12, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Thu 15-Nov-07 18:21 by kellythw

Image text-base: 0x10000000, data-base: 0x114BC884

ROM: 12.2(31r)SG3

Pod Revision 14, Force Revision 34, Tie Revision 32

ITC0004 uptime is 8 hours, 43 minutes

Uptime for this control processor is 7 hours, 54 minutes

System returned to ROM by redundancy reset

System restarted at 12:58:09 cet Sat Dec 8 2007

System image file is "bootflash:cat4000-i5s-mz.122-25.EWA12.bin"

cisco WS-C4510R (MPC8540) processor (revision 11) with 524288K bytes of memory.

Processor board ID FOX11140THS

MPC8540 CPU at 800Mhz, Supervisor V-10GE

Last reset from Redundancy Reset

15 Virtual Ethernet interfaces

296 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.

Configuration register is 0x2102

ITC0004#

Hall of Fame Super Blue

Re: ospf on 3550 vs 4500

Jorge

Not sure what you mean about how do you configure OSPF. ?

As per your example in your original post

router ospf 10

network 10.56.1.0 0.0.0.255 area 0

network 10.57.1.0 0.0.0.255 area 0

etc.

Jon

Hall of Fame Super Bronze

Re: ospf on 3550 vs 4500

Hmm.. That's an open-ended question, how about reading some documentation:

http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124cg/hirp_c/ch15/1chospf.htm

341
Views
0
Helpful
6
Replies
CreatePlease to create content