Hello All
I am having issues with OSPF with VRF and would be grateful to have some insight as to where I am going wrong.
This is setup I have created
CE1 ---- PE ---- CE2
The configurations are as follows:
CE1
-------
!
interface Loopback0
ip address 1.1.1.2 255.255.255.255
!
interface Loopback10
ip address 172.16.0.1 255.0.0.0
!
interface Loopback11
ip address 10.10.10.1 255.255.0.0
!
interface FastEthernet0/1
ip address 129.87.128.18 255.255.255.252
duplex auto
speed auto
!
router ospf 111
router-id 1.1.1.2
log-adjacency-changes
redistribute connected
redistribute static
network 129.87.128.16 0.0.0.3 area 0
default-information originate
!
PE
-------
!
interface Loopback0
ip vrf forwarding client
ip address 1.1.1.1 255.255.255.255
!
interface Loopback1
ip vrf forwarding client
ip address 2.2.2.2 255.255.255.255
!
!
interface FastEthernet0/0
ip vrf forwarding client
ip address 172.26.2.173 255.255.255.248
duplex auto
speed auto
!
interface FastEthernet0/1
ip vrf forwarding client
ip address 129.87.128.17 255.255.255.252
duplex auto
speed auto
!
!
router ospf 111 vrf client
router-id 1.1.1.1
log-adjacency-changes
redistribute connected
redistribute static
redistribute ospf 111 vrf client subnets
network 10.10.0.0 0.0.255.255 area 0
network 10.130.0.0 0.0.255.255 area 0
network 172.26.2.168 0.0.0.7 area 0
network 192.168.1.0 0.0.0.255 area 0
default-information originate
!
router ospf 10 vrf client
router-id 2.2.2.2
log-adjacency-changes
redistribute connected
redistribute static
redistribute ospf 10 vrf client subnets
network 10.10.0.0 0.0.255.255 area 0
network 129.87.128.16 0.0.0.3 area 0
network 172.0.0.0 0.255.255.255 area 0
default-information originate
!
CE2
-------
!
interface Loopback1
ip address 2.2.2.1 255.255.255.255
!
!
interface Loopback10
ip address 10.130.4.1 255.255.0.0
interface Loopback11
ip address 192.168.1.1 255.255.255.0
!
!
interface FastEthernet0/0
ip address 172.26.2.170 255.255.255.248
duplex auto
speed auto
!
!
router ospf 10
router-id 2.2.2.1
log-adjacency-changes
redistribute connected
redistribute static
network 172.26.2.168 0.0.0.7 area 0
default-information originate
!
On the PE the OSPF neigbours seems to be established but I cannot ping CE1 to CE2
sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
2.2.2.1 1 FULL/DR 00:00:31 172.26.2.170 FastEthernet0/0
1.1.1.2 1 FULL/DR 00:00:31 129.87.128.18 FastEthernet0/1
Now I am only able to see one of the loopbacks on the other end but not the other one.
on CE2
O E2 172.0.0.0/8 [110/20] via 172.26.2.173, 00:16:57, FastEthernet0/0
on CE1
O E2 192.168.1.0/24 [110/20] via 129.87.128.17, 00:18:08, FastEthernet0/1
I would be grateful if I can get some advice as to where I am going wrong.
Many Thanks in advance.
