Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

Paris BRI show isdn status deactivated

The Paris telco has onsite and states the BRI line is fine, any ideas?

Does Paris telco has auto spid?

Do I need a special ISDN cable for use in Paris?

Do I have the right hardware ISDN card?

Router#show run

interface BRI0/2/0

no ip address

isdn switch-type vn3

isdn incoming-voice voice

!

interface BRI0/2/1

no ip address

isdn switch-type vn3

isdn incoming-voice voice

!

paris_voip#show isdn status

Global ISDN Switchtype = vn3

ISDN BRI0/2/0 interface

dsl 4, interface ISDN Switchtype = vn3

Layer 1 Status:

DEACTIVATED

Layer 2 Status:

TEI = 64, Ces = 1, SAPI = 0, State = TEI_UNASSIGNED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 4 CCBs = 0

The Free Channel Mask: 0x80000003

ISDN BRI0/2/1 interface

dsl 5, interface ISDN Switchtype = vn3

Layer 1 Status:

DEACTIVATED

Layer 2 Status:

TEI = 65, Ces = 1, SAPI = 0, State = TEI_UNASSIGNED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 5 CCBs = 0

The Free Channel Mask: 0x80000003

Total Allocated ISDN CCBs = 0

paris_voip#

BRI0/2/0 is down, line protocol is down

Hardware is Voice NT or TE BRI

MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation VOICE, loopback not set

1 interface resets

20 carrier transitions

BRI0/2/0:1 is down, line protocol is down

Hardware is Voice NT or TE BRI

0 carrier transitions

BRI0/2/0:2 is down, line protocol is down

Hardware is Voice NT or TE BRI

0 carrier transitions

BRI0/2/1 is down, line protocol is down

Hardware is Voice NT or TE BRI

1 interface resets

18 carrier transitions

BRI0/2/1:1 is down, line protocol is down

Hardware is Voice NT or TE BRI

0 interface resets

0 carrier transitions

BRI0/2/1:2 is down, line protocol is down

Hardware is Voice NT or TE BRI

MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation VOICE, loopback not set

show diag

WIC Slot 2:

VIC2 - BRI-NT/TE Voice daughter card (2 port)

Hardware Revision : 1.1

Top Assy. Part Number : 800-21861-01

Board Revision : B0

Deviation Number : 0-0

Fab Version : 01

PCB Serial Number : FOC09513Q00

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Version Identifier : V

EEPROM format version 4

2 REPLIES
Silver

Re: Paris BRI show isdn status deactivated

When you did the Show ISDN Status your layer 1 is deactivated. That tells you that your are not interfacing with the Telco correctly. You have a layer 1 issue. Do you have an internal NT-1 on your BRI. Your BRI is possibly a S/T unit and does not have the internal NT-1. You may have to get an external unit to interface to the telco. Once your layer 1 comes up you will get assigned your TEI from the telco and you should receive Multi-Frame Established on layer 2 of the command Show ISDN status...Good luck...

Re: Paris BRI show isdn status deactivated

Show diag indicates I have a VIC2-2BRI-NT/TE second generation bri card, CCO states it can handle either network side or user side, but I'm not sure if it's auto detect or a different cables (crossover?).

312
Views
0
Helpful
2
Replies
CreatePlease to create content