Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

PBR on 7600 not implemented in H/W !! ?

Dear all

Would like your assistance plz in verifying why below simple PBR is not implemented in H/W knowing the Copp is not configured

NPE-1#sh ver | i image

System image file is "bootdisk:c7600rsp72043-advipservices-mz.122-33.SRE0a"

NPE-1#sh run int GigabitEthernet1/1

interface GigabitEthernet1/1

ip address 11.0.0.1 255.255.255.0

ip pim sparse-mode

ip policy route-map test  <<-----

ip ospf network point-to-point

load-interval 30

carrier-delay msec 0

mpls ip

mpls traffic-eng tunnels

ip rsvp bandwidth

NPE-1#

NPE-1#sh route-map test

route-map test, permit, sequence 10

  Match clauses:

    ip address (access-lists): 1

  Set clauses:

    ip next-hop 15.0.0.34

  Policy routing matches: 0 packets, 0 bytes

route-map test, permit, sequence 20

  Match clauses:

  Set clauses:

    ip precedence flash

  Policy routing matches: 0 packets, 0 bytes

NPE-1#

NPE-1#sh tcam interface GigabitEthernet1/1 acl in ip

* Global Defaults shared

Entries from Bank 0

Entries from Bank 1

    permit      ip any 224.0.0.0 15.255.255.255

    punt        ip any any   <<<<<--------------------------

NPE-1#

NPE-1#sh policy-map control-plane

NPE-1#

Mayn Thanks

Sherif Ismail

Everyone's tags (3)
4 REPLIES
VIP Super Bronze

PBR on 7600 not implemented in H/W !! ?

Hi Sherif,

When deploying PBR on the 7600, not all actions are hardware based:

The Policy Feature Card (PFC) and any Distributed  Feature Cards (DFCs) provide hardware support for policy-based routing  (PBR) for route-map sequences that use the

match ip address

,

set ip next-hop

, and

ip default next-hop

PBR keywords.

have a look at this link for more info:

http://www.cisco.com/en/US/docs/routers/7600/ios/12.2SR/configuration/guide/layer3.html#wp1027016

HTH

PBR on 7600 not implemented in H/W !! ?

Thanks Reza for your reply

The problem that I am using options that should be implemented in H/W as "match ip address" & "set ip next-hop"

Waiting for your feedback .. thx

VIP Super Bronze

PBR on 7600 not implemented in H/W !! ?

Sherif,

Not sure about this, but if I am reading the output correctly, only ip any any is being punted to CPU and not your set and match clauses.

Reza

PBR on 7600 not implemented in H/W !! ?

Hi Reza

Actually reason for this is due to route-map sequence 20 which mark all traffic with precedence flash

when route-map was configured only with sequence 10, o/p was as below (as I remember)

Entries from Bank 1

    permit      ip any 224.0.0.0 15.255.255.255

    punt        ip 11.0.0.40 any     

    permit      ip any any

NPE-1#

I know a provider who did a swap from 7600 routers to another vendor due to this issue ... he was configuring several PBRs and this caused high CPU utilization due to router S/W processing

BR,
Sherif Ismail

537
Views
3
Helpful
4
Replies
CreatePlease login to create content