Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Performance Routing Pfr / OER Woes........

Hello again Guy's

Im trying to get PFR working and having a few issues in lab enviroment, I am currently just looking to get a basic PFR fast failover to 192.168.3.0/24, upon which i can build further policies/labs. But alas i am having little luck......

PS The master is also a BR:

Firstly the 2 BGP Routes at the MC:

*> 192.168.3.0      172.31.0.1                           200 4445 4445 i

* i                 192.168.200.2            0    100      0 i

With a secondary static for good measure:

#show run | i ip route

ip route 0.0.0.0 0.0.0.0 192.168.2.250

ip route 192.168.3.0 255.255.255.0 192.168.2.253 255 name TestSecondaryRoutePFR

#show pfr master

OER state: ENABLED and ACTIVE

  Conn Status: SUCCESS, PORT: 3949

  Version: 3.0

  Number of Border routers: 2

  Number of Exits: 2

  Number of monitored prefixes: 0 (max 1000)

  Max prefixes: total 1000 learn 2500

  Prefix count: total 0, learn 0, cfg 0

  PBR Requirements met

  Nbar Status: Inactive

Border           Status   UP/DOWN             AuthFail  Version

192.168.2.254    ACTIVE   UP       00:01:44          0  3.0

192.168.2.253    ACTIVE   UP       00:01:44          0  3.0

Global Settings:

  max-range-utilization percent 20 recv 0

  mode route metric bgp local-pref 5000

  mode route metric static tag 5000

  mode route protocol pbr

  trace probe delay 1000

  logging

  exit holddown time 60 secs, time remaining 0

Default Policy Settings:

  backoff 180 360 180

  delay relative 50

  holddown 90

  periodic 90

  probe frequency 56

  number of jitter probe packets 100

  mode route control

  mode monitor both

  mode select-exit best

  loss relative 10

  jitter threshold 20

  mos threshold 3.60 percent 30

  unreachable relative 50

  resolve delay priority 11 variance 20

  resolve range priority 12 variance 0

  resolve utilization priority 13 variance 20

Learn Settings:

  current state : STARTED

  time remaining in current state : 107 seconds

  throughput

  delay

  no inside bgp

  traffic-class filter access-list DENY_GLOBAL_LEARN_LIST

  monitor-period 1

  periodic-interval 0

  aggregation-type prefix-length 24

  prefixes 100 appls 100

  expire after time 30

  Learn-List seq 20 refname Learn_List_Remote1_Prefix

    Configuration:

     Traffic-Class Prefix-list: Remote1_Subnets

     Aggregation-type: prefix-length 24

     Learn type: throughput

     Session count: 50 Max count: 100

     Status: INACTIVE

    Stats:

     Traffic-Class Count: 0

#show pfr master active-probes

        OER Master Controller active-probes

Border   = Border Router running this Probe

State    = Un/Assigned to a Prefix

Prefix   = Probe is assigned to this Prefix

Type     = Probe Type

Target   = Target Address

TPort    = Target Port

How      = Was the probe Learned or Configured

N - Not applicable

The following Probes exist:

State      Prefix             Type     Target          TPort   How     Codec

Unassigned                    echo     192.168.3.254       N  Cfgd         N <-- ?

The following Probes are running:

Border          State    Prefix             Type     Target          TPort

Nothing.......?

Config on MC:

pfr master

policy-rules Remote_1_General

logging

!

border 192.168.2.254 key-chain prf

  interface FastEthernet0/1 internal

  interface FastEthernet0/0.100 external

   max-xmit-utilization percentage 80

   link-group MPLS

!

border 192.168.2.253 key-chain prf

  interface FastEthernet0/1 internal

  interface Tunnel0 external

   link-group DMVPN

!

learn

  throughput

  delay

  periodic-interval 0

  monitor-period 1

  traffic-class filter access-list DENY_GLOBAL_LEARN_LIST

  expire after time 30

  list seq 20 refname Learn_List_Remote1_Prefix

   traffic-class prefix-list Remote1_Subnets

   throughput

max prefix total 1000

holddown 90

backoff 180 360

mode route protocol pbr

mode route control

mode select-exit best

periodic 90

!

active-probe echo 192.168.3.254

pfr border

logging

local FastEthernet0/1

master 192.168.2.254 key-chain prf

pfr-map Remote_1_General 100

match pfr learn list Remote1_Subnets

set periodic 90

set mode route control

set mode monitor fast

set resolve utilization priority 2 variance 10

no set resolve range

set unreachable threshold 100000

set active-probe echo 192.168.3.254

set probe frequency 4

Prefix list: ip prefix-list Remote1_Subnets seq 5 permit 192.168.3.0/24

Any Help would be much appriceated as always.

Regards Neil

Regards Neil http://uk.linkedin.com/pub/neil-grant/20/5b0/267
Everyone's tags (5)
1 REPLY
Cisco Employee

Performance Routing Pfr / OER Woes........

Hello,

You have defined a learn-list called "Learn_List_Remote1_Prefix" in your learning section.

But in your pfr-map you reference the access-list instead of the learn-list. If you plan to use the automatic learning, then you have to use the learn-list name in your pfr map, ie:

pfr-map Remote_1_General 100

match pfr learn list Learn_List_Remote1_Prefix

Cheers.

/jmb

989
Views
0
Helpful
1
Replies