I am with problems on the my connection ppp. I created static router, the communication between routers is established, I obtain connection to IP of the LAN port on the routers, the my problem is that I do not obtain connection the stations of the side of the LAN, only until the IP of the port LAN of routers. What it is necessary so that the communication continues until its final destination?
Solved! Go to Solution.
If you can reach the LAN of the remote router and the remote router can reach your LAN, then routing is functioning properly.
If the workstations at either LAN can't ping each other, then make sure the default gateway of the workstations are pointing to their respective LAN IP of the local router.
Edison and friends, exactly, I don't not understand which is problem.
See my scene.
Default gateway on the network 220.127.116.11/24 is 18.104.22.168
RouterX (WAN IP 10.0.0.10)
RouterX (LAN IP 22.214.171.124)
RouterY (WAN IP 10.0.0.20)
RouterY (LAN IP 126.96.36.199)
The static router for routerX is 188.8.131.52 255.255.255.0 10.0.0.2
The static router for routerY is 0.0.0.0 0.0.0.0 10.0.0.1
My problem is that the hosts on the network 184.108.40.206/24 do not obtain communication with hosts on the network 220.127.116.11/24 through of the router 18.104.22.168.
These switches will be only used for the communication point to point with other place.
In this other place does not exist other router, only the router 22.214.171.124, different of the other place that have the default gateway (126.96.36.199) and the router for this communication.
The return on the communication is necessary? Is necessary a route on the router 188.8.131.52 for the router 184.108.40.206? As the router 220.127.116.11 is the default gateway for all hosts on the network 18.104.22.168/24 is necessary a static route in this router for the router 22.214.171.124?
Sincerely, I don't understand the cause of the problem in this communication.
Analysing my scene which configurations is necessary ?
1) The default gateway on hosts located in 126.96.36.199/24 should be 188.8.131.52 - Router X LAN interface - NOT 184.108.40.206.
2) The static route on Router X for 220.127.116.11/24 should be 10.0.0.20 - Router Y WAN interface - NOT 10.0.0.2
3) The static route on Router Y should use the gateway of 10.0.0.10 - Router X WAN interface - NOT 10.0.0.1
I wrote wrong, your reply for questions 2 and 3 is correctly but for the question 1 you it did not understand. I have two routers on the network 18.104.22.168/24, the default router 22.214.171.124) that use for communication with internet and others places (example: USA, England) and the other router (126.96.36.199) which use for point to point communication. I want that the hosts of the network 188.8.131.52/24 obtain communication with the network 184.108.40.206/24. OK?
...exactly, this for communications of the hosts on the network 220.127.116.11/24 for the hosts on the network 18.104.22.168/24, but for communication of the hosts on the network 22.214.171.124/24 for the hosts on the network 126.96.36.199, remember that in this network does not exist other router, only the router 188.8.131.52 and this obtain connection normally the LAN port of the router 184.108.40.206, but not the hosts of the network 220.127.116.11/24.
Don't you have a default route on the router hosting 18.104.22.168/24 pointing back to the router hosting 22.214.171.124/24?
Well, that should take care of all routes.
Sorry, I did not understand. The ping command of the host on the network 126.96.36.199/24 it functions without problems until the LAN port of router 188.8.131.52 (184.108.40.206), but not in hosts of the same network of router.
It won't work until you add the route to the 53.0/24 network in the 52.254 router.
This route should point to 52.10
In the 52.254 router do:
ip route 220.127.116.11 255.255.255.0 18.104.22.168