Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

PPP Multilink Issue on 7206

We have 6 new T1's coming in on a T1 card on a 7206. We are having a problem with PPP multilink on this card. Here is the configuration for the multilink and each of the T1s:

interface Multilink1

ip address 10.105.255.174 255.255.255.252

ppp multilink

multilink-group 1

interface Serial1/0:0

bandwidth 1536

no ip address

ip load-sharing per-packet

encapsulation ppp

fair-queue

ppp multilink

multilink-group 1

!

Here is the ppp debugs out of the log:

00:14:17: Se1/0:0 PPP: Phase is ESTABLISHING, Passive Open [0 sess, 1 load]

00:14:17: Se1/0:0 LCP: State is Listen

00:14:17: Se1/0:0 LCP: I CONFREQ [Listen] id 199 len 23

00:14:17: Se1/0:0 LCP: MagicNumber 0x8526341E (0x05068526341E)

00:14:17: Se1/0:0 LCP: MRRU 1500 (0x110405DC)

00:14:17: Se1/0:0 LCP: EndpointDisc 1 Core-1 (0x130901436F72652D31)

00:14:17: Se1/0:0 LCP: O CONFREQ [Listen] id 111 len 22

00:14:17: Se1/0:0 LCP: MagicNumber 0x90BF199B (0x050690BF199B)

00:14:17: Se1/0:0 LCP: MRRU 1524 (0x110405F4)

00:14:17: Se1/0:0 LCP: EndpointDisc 1 ABRHQ (0x1308014142524851)

00:14:17: Se1/0:0 LCP: O CONFACK [Listen] id 199 len 23

00:14:17: Se1/0:0 LCP: MagicNumber 0x8526341E (0x05068526341E)

00:14:17: Se1/0:0 LCP: MRRU 1500 (0x110405DC)

00:14:17: Se1/0:0 LCP: EndpointDisc 1 Core-1 (0x130901436F72652D31)

00:14:17: Se1/0:0 LCP: I CONFACK [ACKsent] id 111 len 22

00:14:17: Se1/0:0 LCP: MagicNumber 0x90BF199B (0x050690BF199B)

00:14:17: Se1/0:0 LCP: MRRU 1524 (0x110405F4)

00:14:17: Se1/0:0 LCP: EndpointDisc 1 ABRHQ (0x1308014142524851)

00:14:17: Se1/0:0 LCP: State is Open

00:14:17: Se1/0:0 MLP: Request add link to bundle

00:14:17: Se1/0:0 PPP: Phase is VIRTUALIZED [0 sess, 1 load]

00:14:17: Se1/0:0 MLP: Adding link to bundle

00:14:17: Mu1 MLP: Added first link Se1/0:0 to bundle Core-1

00:14:17: Se1/0:0 LCP: I TERMREQ [Open] id 200 len 4

00:14:17: Mu1 MLP: No previous member for idle link in 'Core-1'

00:14:17: Se1/0:0 LCP: O TERMACK [Open] id 200 len 4

00:14:17: Se1/0:0 MLP: Request drop link from bundle Mu1

00:14:17: Se1/0:0 PPP: Phase is TERMINATING [0 sess, 1 load]

00:14:17: Mu1 MLP: Removing link Se1/0:0 from bundle Core-1

00:14:17: Mu1 MLP: Dropped link Se1/0:0 from bundle Core-1

00:14:17: Mu1 MLP: Dropped last link, removing bundle Core-1

00:14:17: Mu1 MLP: Removing bundle 'Core-1'

00:14:17: Mu1 LCP: State is Closed

00:14:17: Se1/1:0 LCP: TIMEout: State TERMsent

00:14:17: Se1/1:0 LCP: State is Closed

00:14:17: Se1/1:0 PPP: Phase is DOWN [0 sess, 1 load]

When setting up the link as an HDLC link or even PPP without multilink, the connection is fine. Only when the link is changed to a multilink do we see this. The multilink will bounce (coming up for less than a second then going back down.) We see the interfaces in the multilink as up/down.

Any recommendations?

Greg

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: PPP Multilink Issue on 7206

Hi, since the termination request is received by the router you sent debug and config, I think the same info would be needed about the other router.

3 REPLIES
Hall of Fame Super Silver

Re: PPP Multilink Issue on 7206

Greg

I am curious about what appears to be 2 names for multilink that show up in the output that you posted:

00:14:17: Se1/0:0 MLP: Request add link to bundle

00:14:17: Se1/0:0 PPP: Phase is VIRTUALIZED [0 sess, 1 load]

00:14:17: Se1/0:0 MLP: Adding link to bundle

00:14:17: Mu1 MLP: Added first link Se1/0:0 to bundle Core-1

00:14:17: Se1/0:0 LCP: I TERMREQ [Open] id 200 len 4

00:14:17: Mu1 MLP: No previous member for idle link in 'Core-1'

00:14:17: Se1/0:0 LCP: O TERMACK [Open] id 200 len 4

00:14:17: Se1/0:0 MLP: Request drop link from bundle Mu1

Perhaps a more full view of the router config might shed a bit more light on the issue.

HTH

Rick

New Member

Re: PPP Multilink Issue on 7206

Building configuration...

Current configuration : 4276 bytes

!

! Last configuration change at 09:12:55 CST Wed Jun 25 2008

! NVRAM config last updated at 09:16:04 CST Wed Jun 25 2008

!

version 12.2

no service pad

service timestamps debug uptime

service timestamps log uptime

service password-encryption

!

clock timezone CST -6

ip subnet-zero

no ip source-route

ip flow-cache timeout active 1

ip cef

!

!

!

no mpls traffic-eng auto-bw timers frequency 0

call rsvp-sync

!

!

!

!

!

!

controller T1 1/0

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 1/1

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 1/2

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 1/3

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 1/4

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 1/5

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 1/6

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 1/7

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

!

class-map match-all video1

match access-group 102

class-map match-all voice1

match access-group 101

!

!

policy-map video-police

class voice1

bandwidth 384

class video1

bandwidth 384

class class-default

fair-queue 64

queue-limit 20

!

!

!

interface Loopback0

ip address 10.253.0.65 255.255.255.255

no clns route-cache

!

interface Multilink1

description 3MB to Colo4Dallas

ip address 10.105.255.174 255.255.255.252

ip flow ingress

ip nbar protocol-discovery

service-policy output video-police

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/0:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/1:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/2:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/3:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/4:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/5:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/6:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface Serial1/7:0

bandwidth 1536

no ip address

ip flow ingress

encapsulation ppp

ppp multilink

multilink-group 1

no clns route-cache

!

interface FastEthernet2/0

bandwidth 100000

ip address 10.105.50.1 255.255.255.0

ip flow ingress

no ip route-cache cef

no ip route-cache

shutdown

duplex full

no clns route-cache

!

ip classless

ip route 0.0.0.0 0.0.0.0 10.105.255.173

ip route 10.253.0.2 255.255.255.255 10.105.255.173

ip flow-export source FastEthernet2/0

ip flow-export version 5

ip flow-export destination 10.50.66.218 9996

!

ip http server

!

!

!

logging trap debugging

logging 10.50.66.218

access-list 101 permit ip any any precedence critical

access-list 102 permit ip any any precedence flash-override

!

snmp-server community publ1c RW

snmp-server community public RO

snmp-server enable traps tty

snmp-server enable traps sonet

!

!

control-plane

!

!

dial-peer cor custom

!

!

!

!

line con 0

stopbits 1

line aux 0

stopbits 1

line vty 0 4

login

!

!

end

I took a couple things out- but this is the config.

Hall of Fame Super Gold

Re: PPP Multilink Issue on 7206

Hi, since the termination request is received by the router you sent debug and config, I think the same info would be needed about the other router.

528
Views
0
Helpful
3
Replies