Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

PPP Multipoint (Inactive) - ???

I am configuring PPP Multipoint on a 6509 and a 2621

Here is the output of sh ppp multilink on the 6509:

No active bundles

Multilink1 (inactive)
  Member links: 3
    Se8/0/0:0 (inactive)
    Se8/0/1:0 (inactive)
    Se8/0/2:0 (inactive)

Here is the output of sh ppp multilink on the 2600:

No active bundles

Multilink1 (inactive)
  Member links: 3
    Se0/1 (inactive)
    Se0/2 (inactive)
    Se0/3 (inactive)

Here is the 6509 config:

interface Multilink1

ip address 100.1.1.1 255.255.255.252

ppp multilink

multilink-group 1

!

interface Serial8/0/0:0

description FN Multilink Interface 1

no ip address

encapsulation ppp

no fair-queue

ppp multilink

multilink-group 1

!

interface Serial8/0/1:0

description FN Multilink Interface 2

no ip address

encapsulation ppp

no fair-queue

ppp multilink

multilink-group 1

!

interface Serial8/0/2:0

description FN Multilink Interface 3

no ip address

encapsulation ppp

no fair-queue

ppp multilink

multilink-group 1

!

Here is the 2600 config:

interface Multilink1

ip address 100.1.1.2 255.255.255.252

service-policy output voice-policy

ppp multilink

multilink-group 1

!

interface Serial0/1

description FN Multilink INT 3

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/2

description FN Multilink INT 2

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/3

description FN Multilink INT 1

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!
interface Serial0/1
description FN Multilink INT 3
no ip address
encapsulation ppp
ppp multilink
multilink-group 1
!
interface Serial0/2
description FN Multilink INT 2
no ip address
encapsulation ppp
ppp multilink
multilink-group 1
!
interface Serial0/3
description FN Multilink INT 1
no ip address
encapsulation ppp
ppp multilink
multilink-group 1
!

any ideas???

  • WAN Routing and Switching
Everyone's tags (2)
7 REPLIES
New Member

PPP Multipoint (Inactive) - ???

The 2600 config double pasted it should be this:

Here is the 2600 config:

interface Multilink1

ip address 100.1.1.2 255.255.255.252

service-policy output voice-policy

ppp multilink

multilink-group 1

!

interface Serial0/1

description FN Multilink INT 3

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/2

description FN Multilink INT 2

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/3

description FN Multilink INT 1

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

PPP Multipoint (Inactive) - ???

Hi Brian,

Seems like your are using controller on 6509.

If yes, can you check if controller 8/0/0 , 8/0/1 and 8/0/2 is no shut.

Regards,

Smitesh

New Member

PPP Multipoint (Inactive) - ???

I went into each controller and did a not shut. The multilinks show inactive on both the 2600 and 6509.  The three T1s are all up and running. Each shows line up, protocol down.

More 6509 config:

controller T1 8/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/3

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/4

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/5

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/6

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/7

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

controller T1 8/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/3

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/4

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/5

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/6

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/7

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

New Member

PPP Multipoint (Inactive) - ???

I tried doing a no shut on the 3 controlles. The T1s are up and running. Each shows line up and protocol down.

New Member

Re: PPP Multipoint (Inactive) - ???

Yes I tried doing a no shut on each. The T1s show line up, protocol down.

Here is the controller config on the 6509. Do the three controllers

(8/0/0 - 2) need to be in the same channel group?

controller T1 8/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/3

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/4

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/5

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/6

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/7

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

Re: PPP Multipoint (Inactive) - ???

Can you also add command clock source line under controller config ?

New Member

Re: PPP Multipoint (Inactive) - ???

I moved the config to another 2PA Flexwan Module and the Multilink came

up. I apparently have a bad module. Thanks for all your help.

2727
Views
0
Helpful
7
Replies