Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

pppoe cant be removed !

hi,

i have this configuration:

!

interface FastEthernet3/0

ip address 10.0.0.1 255.255.255.0

ip nat inside

ip tcp adjust-mss 1452

duplex auto

speed auto

pppoe enable

pppoe-client dial-pool-number 6

pppoe-client dial-pool-number 5

pppoe-client dial-pool-number 4

!

when i try:

#conf

<config>#int fast3/0

<config-if>#no pppoe-client dialer-pool-number 4

it just wont be removed!

on my other fastethernet intefaces i am able to remove it with the same command

how do i find out what is wrong??

thanks

Cisco IOS Software, 3800 Software (C3845-IPBASE-M), Version 12.4(3d), RELEASE SO

FTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Wed 19-Apr-06 08:56 by alnguyen

ROM: System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)

uptime is 1 hour, 37 minutes

System returned to ROM by reload at 06:25:55 GMT3 Tue Sep 11 2007

System restarted at 06:26:41 GMT3 Tue Sep 11 2007

System image file is "flash:c3845-ipbase-mz.124-3d.bin"

Cisco 3845 (revision 1.0) with 223232K/38912K bytes of memory.

Processor board ID FCZ102770EV

2 FastEthernet interfaces

2 Gigabit Ethernet interfaces

2 Token Ring interfaces

8 ATM interfaces

DRAM configuration is 64 bits wide with parity enabled.

479K bytes of NVRAM.

62720K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

3 REPLIES

Re: pppoe cant be removed !

Still you have the correct syntax:

pppoe-client dial-pool-number

To configure a PPP over Ethernet (PPPoE) client and to specify dial-on-demand routing (DDR) functionality, use the pppoe-client dial-pool-number command in either interface configuration mode or ATM virtual circuit configuration mode. To disable any configured functionality, use the no form of this command.

pppoe-client dial-pool-number number [dial-on-demand]

no pppoe-client dial-pool-number number [dial-on-demand]

Can you try if it works when you shutdown the ethernet interface first?

regards,

Leo

Community Member

Re: pppoe cant be removed !

hi thanks,

no it wont be removed!

i tried shutting the interface then no pppoe-client dial-pool-number 4, it wont be removed.

i tried no pppoe enable, then all of the dial pools has been removed, but when i enable it again by pppoe enable, all the pppoe-client come back.

help please!

Community Member

Re: pppoe cant be removed !

hi, i did some comparision between my 2 fast eth, there is only one diffrence that i found:

Router#sh int fast3/0 switching

FastEthernet3/0

Throttle count 0

Drops RP 0 SP 0

SPD Flushes Fast 0 SSE 0

SPD Aggress Fast 0

SPD Priority Inputs 4697 Drops 0

Protocol IP

Switching path Pkts In Chars In Pkts Out Chars Out

Process 126 17234 217 14004

Cache misses 0 - - -

Fast 0 0 163 10938

Auton/SSE 0 0 0 0

Protocol DEC MOP

Switching path Pkts In Chars In Pkts Out Chars Out

Process 0 0 230 17710

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

Protocol ARP

Switching path Pkts In Chars In Pkts Out Chars Out

Process 4697 300608 7439 446340

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

Protocol CDP

Switching path Pkts In Chars In Pkts Out Chars Out

Process 0 0 2389 947152

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

Protocol Other

Switching path Pkts In Chars In Pkts Out Chars Out

Process 0 0 14076 844560

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

Router#sh int fast4/0 switching

FastEthernet4/0

Protocol DEC MOP

Switching path Pkts In Chars In Pkts Out Chars Out

Process 0 0 116 8932

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

Protocol ARP

Switching path Pkts In Chars In Pkts Out Chars Out

Process 0 0 9 540

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

Protocol CDP

Switching path Pkts In Chars In Pkts Out Chars Out

Process 0 0 15 4911

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

Protocol Other

Switching path Pkts In Chars In Pkts Out Chars Out

Process 0 0 6957 417420

Cache misses 0 - - -

Fast 0 0 0 0

Auton/SSE 0 0 0 0

by the way, both fast eth have EXACTLY the same cfg, i am not sure why they are diffrent in this output, might this help? please let me know..

117
Views
0
Helpful
3
Replies
CreatePlease to create content