08-17-2013 05:23 AM - edited 03-04-2019 08:47 PM
Dear Experts
We have Cisco7606-S with two RSP720-3C-GE,When we install both RSP on the router,then the router show the NVRAM size at 2044K but when we boot the router with one RSP then the Size of NVRAM is Ok at 3096K,Please help me who we can solve this problem,Following please find the Show version in both Condition
Also I have attached the Boot procedure when the router boot with two RSP Card
Router#sh vers
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 12.2(33)SRC6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Mon 08-Mar-10 10:39 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
Router uptime is 4 minutes
Uptime for this control processor is 4 minutes
System returned to ROM by power cycle (SP by power on)
System image file is "bootdisk:c7600rsp72043-adventerprisek9-mz.122-33.SRC6.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco CISCO7606-S (M8500) processor (revision 1.1) with 851968K/65536K bytes of memory.
Processor board ID FOX1623G5WV
BASEBOARD: RSP720
CPU: MPC8548_E, Version: 2.1, (0x80390021)
CORE: E500, Version: 2.2, (0x80210022)
CPU:1200MHz, CCB:400MHz, DDR:200MHz,
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Last reset from power-on
1 Virtual Ethernet interface
48 FastEthernet interfaces
52 Gigabit Ethernet interfaces
3964K bytes of non-volatile configuration memory.
507024K bytes of Internal ATA PCMCIA card (Sector size 512 bytes).
Configuration register is 0x2102
08-17-2013 09:19 AM
08-17-2013 11:01 PM
Excuseme,I have not found any discussion like my problem,can you please help me who have the same problem to find the solution,it is very urgent problem for us
Thank you so much for your cooperation
08-17-2013 11:52 PM
Hi,
Actually you are not seeing a problem at all because the design itself is such by Cisco for some internal reasons.
So you need not be worried about that. If you need to check the actualy size of the NVRAM on the device (both Active & Standby RSP), kindly use the command "show file system". This would give you accurate results.
***********Plz do rate this post if you found it helpful*************************
Thanks & Regards,
Vignesh R P
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide