Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Problem of NVRAM Size on Cisco7606-S

Dear Experts

We have  Cisco7606-S with two RSP720-3C-GE,When we install both RSP on the router,then the router show the NVRAM size at 2044K but when we boot the router with one RSP then the Size of NVRAM is Ok at 3096K,Please help me who we can solve this problem,Following please find the Show version in both Condition

Also I have attached the Boot procedure when the router boot with two RSP Card

Router#sh vers

Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 12.2(33)SRC6, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2010 by Cisco Systems, Inc.

Compiled Mon 08-Mar-10 10:39 by prod_rel_team

ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)

Router uptime is 4 minutes

Uptime for this control processor is 4 minutes

System returned to ROM by  power cycle (SP by power on)

System image file is "bootdisk:c7600rsp72043-adventerprisek9-mz.122-33.SRC6.bin"

Last reload type: Normal Reload

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

        

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco CISCO7606-S (M8500) processor (revision 1.1) with 851968K/65536K bytes of memory.

Processor board ID FOX1623G5WV

BASEBOARD: RSP720

CPU: MPC8548_E, Version: 2.1, (0x80390021)

CORE: E500, Version: 2.2, (0x80210022)

CPU:1200MHz, CCB:400MHz, DDR:200MHz,

L1:    D-cache 32 kB enabled

        I-cache 32 kB enabled

Last reset from power-on

1 Virtual Ethernet interface

48 FastEthernet interfaces

52 Gigabit Ethernet interfaces

3964K bytes of non-volatile configuration memory.

507024K bytes of Internal ATA PCMCIA card (Sector size 512 bytes).

Configuration register is 0x2102

3 REPLIES
Hall of Fame Super Gold

Problem of NVRAM Size on Cisco7606-S

Already discussed in another thread, please do not post duplicates.

New Member

Problem of NVRAM Size on Cisco7606-S

Excuseme,I have not found any discussion like my problem,can you please help me who have the same problem to find the solution,it is very urgent problem for us

Thank you so much for your cooperation

Problem of NVRAM Size on Cisco7606-S

Hi,

Actually you are not seeing a problem at all because the design itself is such by Cisco for some internal reasons.

So you need not be worried about that. If you need to check the actualy size of the NVRAM on the device (both Active & Standby RSP), kindly use the command "show file system". This would give you accurate results.

***********Plz do rate this post if you found it helpful*************************

Thanks & Regards,

Vignesh R P

219
Views
0
Helpful
3
Replies