07-29-2013 04:50 AM - edited 03-04-2019 08:34 PM
Hi ,
I have a problem with Switch Catalyst 2950 T . At startup I see following error and SYST light blink green .
I did the update IOS but did not change .
Please help me to solve the problem.
Thank you
Done initializing flashfs.
POST: System Board Test : Passed
POST: Ethernet Controller Test : Passed
ASIC Initialization Passed
SCHAN_HDR <CPU=0 COS=0 ECODE=0 EBIT=0
LEN=0 SRC=5 DST=0 OP=7=READ_MEM_CMD>
SCHAN_DW[0]=0x1C014000
SCHAN_DW[1]=0x03000019
SCHAN_DW[2]=0x80CBA418
SCHAN_DW[3]=0x00000018
SCHAN_DW[4]=0x802B9238
SCHAN_DW[5]=0x802B9224
SCHAN_DW[6]=0x00000010
%PLATFORM_HW-3-MEM_READ_FAILURE:
Read memory failed for memory VTABLE at index 1
SCHAN_HDR <CPU=0 COS=0 ECODE=0 EBIT=0
LEN=0 SRC=5 DST=0 OP=7=READ_MEM_CMD>
SCHAN_DW[0]=0x1C014000
SCHAN_DW[1]=0x05000001
SCHAN_DW[2]=0x80CBA398
SCHAN_DW[3]=0x80CBA470
SCHAN_DW[4]=0x00000039
POST: Loop back Test Failed on FastEthernet0/1. State:Disabled
Solved! Go to Solution.
07-29-2013 05:19 AM
Hi,
This is explained here and it states you should contact TAC if this reoccurs:
Regards
Alain
Don't forget to rate helpful posts.
07-29-2013 05:24 AM
Hi,
This is HW failure. Either memory is corrupted or switch has HW failure and cannot read it correctly. You should replace it.
Kind Regards,
Ivan Shirshin
**Please grade this post if you find it useful.
07-29-2013 05:19 AM
Hi,
This is explained here and it states you should contact TAC if this reoccurs:
Regards
Alain
Don't forget to rate helpful posts.
07-30-2013 10:47 PM
Hi ,
Thank you for reply.
According to this description, I have to replace the device.
Best Regard
07-29-2013 05:24 AM
Hi,
This is HW failure. Either memory is corrupted or switch has HW failure and cannot read it correctly. You should replace it.
Kind Regards,
Ivan Shirshin
**Please grade this post if you find it useful.
07-29-2013 03:27 PM
%PLATFORM_HW-3-MEM_READ_FAILURE:
Pop the lid, clean the connecting tips of the memory. Put it back in and pray it'll work.
07-30-2013 10:51 PM
Hi ,
Thank you for reply .
Where is a memory chip on the motherboard ? I Cant find it !
Reagard
07-30-2013 11:20 PM
Ooops. 2950. No. No memory.
The memory is wielded to the mother board. There's another method ... not "fully" recommended (but I've done it before).
Bang it a few times on the flat side.
NOTE: I AM serious.
07-31-2013 02:31 AM
Leo,
But actually your idea about cleaning the tips is sound. Even if there are only chips soldered on the motherboard, there is a (admittedly remote) chance that their pins, if accessible, have become covered with dust and have thus developed some kind of coupling, impairing their function. Dusting off the pins with a brush and compressed air could do the trick...
Best regards,
Peter
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: