Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

qos in 10G

Hi,

I have 2Cat6506 working in VSS.

I need to give priority to traffic with DSCP = 46 (CoS = 5) in a 10G link, I've seen that QoS scheduling is:

Rx: 1p7q2t

Tx: 1p7q4t

priority queue for TX is 8. Default configuration is that traffic DSCP = 46 goes to that queue, but it is not in RX (priority queue is 8 and DSCP=46 to queue 1):

catalyst#sh queueing int ten1/7/1

Interface TenGigabitEthernet1/7/1 queueing strategy: Weighted Round-Robin

Port QoS is enabled

Port is untrusted

Extend trust state: not trusted [COS = 0]

Default COS is 0

Queueing Mode In Tx direction: mode-cos

Transmit queues [type = 1p7q4t]:

Queue Id Scheduling Num of thresholds

-----------------------------------------

01 WRR 04

02 WRR 04

03 WRR 04

04 WRR 04

05 WRR 04

06 WRR 04

07 WRR 04

08 Priority 01

...

queue thresh cos-map

---------------------------------------

1 1 0

1 2 1

1 3

1 4

2 1 2

2 2 3 4

2 3

2 4

3 1 6 7

3 2

3 3

3 4

4 1

4 2

4 3

4 4

5 1

5 2

5 3

5 4

6 1

6 2

6 3

6 4

7 1

7 2

7 3

7 4

8 1 5

queue thresh dscp-map

---------------------------------------

1 1 0 1 2 3 4 5 6 7 8 9 11 13 15 16 17 19 21 23 25 27 29 31 33 39 41 42 43 44 45 47

1 2

1 3

1 4

2 1 14

2 2 12

2 3 10

2 4

3 1 22

3 2 20

3 3 18

3 4

4 1 24 30

4 2 28

4 3 26

4 4

5 1 32 34 35 36 37 38

5 2

5 3

5 4

6 1 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

6 2

6 3

6 4

7 1

7 2

7 3

7 4

8 1 40 46

Queueing Mode In Rx direction: mode-cos

Receive queues [type = 1p7q2t]:

Queue Id Scheduling Num of thresholds

-----------------------------------------

01 WRR 02

02 WRR 02

03 WRR 02

04 WRR 02

05 WRR 02

06 WRR 02

07 WRR 02

08 Priority 01

queue thresh cos-map

---------------------------------------

1 1 0 1 2 3 4 5 6 7

1 2

2 1

2 2

3 1

3 2

4 1

4 2

5 1

5 2

6 1

6 2

7 1

7 2

8 1

queue thresh dscp-map

---------------------------------------

1 1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

1 2

2 1

2 2

3 1

3 2

4 1

4 2

5 1

5 2

6 1

6 2

7 1

7 2

8 1

Is ther any way to set the value DSCP = 46 in the queue 8 for RX? can be done in mode configuration or must be done in interface configuration?

232
Views
0
Helpful
0
Replies