Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Question about maximum path issue on ASR

Hello. : )

One question. 

 

what does this log mean?

 

fib_mgr[173]: %PLATFORM-PLAT_FIB-3-ERROR_HW_LIMIT_RT : This line card supports only maximum 8 paths for a recursive prefix, please change the configs to not exceed 8 paths or else system behaviour will be sub optimal   : pkg/bin/fib_mgr : (PID=462954) :  -Traceback= 4d201284 4d019a24 4d01b4bc 4cdc19e4 4ccb4758 4ccb1fd4 4cc23cd8 400a86c0 400a913c 400a97f0 400b2250 4006f154 40077dbc 400501d8 400e14c0 400e2384

 

 

Is this routing problem?

Why this occurred? and what should i do to fix this ?

/////////////////////////////////////////////////

router static
 address-family ipv4 unicast
  20.1.2.0/24 1.1.1.4
  20.1.2.0/24 1.1.2.5
  20.1.2.0/24 1.1.3.5
  20.1.2.0/24 1.1.4.5
  20.1.2.0/24 1.1.5.5
  20.1.2.0/24 1.1.6.5
  20.1.2.0/24 1.1.7.5
  20.1.2.0/24 1.1.8.5
  20.1.2.0/24 1.1.9.5
  20.1.2.0/24 1.1.10.5
  20.1.2.0/24 1.1.11.5
  20.1.2.0/24 1.1.12.5
  20.1.2.0/24 1.1.13.5
  20.1.2.0/24 1.1.14.5
  20.1.2.0/24 1.1.15.5
  20.1.2.0/24 1.1.16.5
  20.1.2.0/24 1.1.17.5
  20.1.2.0/24 1.1.18.5
  20.1.2.0/24 1.1.19.5
  20.1.2.0/24 1.1.20.5
  192.168.10.0/24 192.168.0.1
 !
 vrf TEST_VRF
  address-family ipv4 unicast
   0.0.0.0/0 38.10.1.5
  !
 !
!
router ospf 2
 area 0
  bfd minimum-interval 200
  bfd multiplier 5
  interface TenGigE0/7/0/0
   bfd fast-detect
  !
 !
!
router ospf 100
 router-id 172.30.4.4
 network point-to-point
 microloop avoidance rib-update-delay 5000
 microloop avoidance protected
 auto-cost reference-bandwidth 100000
 redistribute connected
 redistribute static
 area 0
  fast-reroute per-prefix
  fast-reroute per-prefix remote-lfa tunnel mpls-ldp
  interface Loopback0
   passive enable
  !
  interface GigabitEthernet0/0/0/2
  !
  interface TenGigE0/0/1/0
  !
  interface TenGigE0/0/1/2
  !
  interface TenGigE0/0/1/3
  !
//////////////////////////////////////////////////////////

 

Device is ASR9K and here is the configuration. 

 

 

 

Thank you in advance : 0

 

 

 

  • WAN Routing and Switching
52
Views
0
Helpful
0
Replies
This widget could not be displayed.