cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
217
Views
0
Helpful
0
Replies

Question about maximum path issue on ASR

CATYO
Level 1
Level 1

Hello. : )

One question. 

 

what does this log mean?

 

fib_mgr[173]: %PLATFORM-PLAT_FIB-3-ERROR_HW_LIMIT_RT : This line card supports only maximum 8 paths for a recursive prefix, please change the configs to not exceed 8 paths or else system behaviour will be sub optimal   : pkg/bin/fib_mgr : (PID=462954) :  -Traceback= 4d201284 4d019a24 4d01b4bc 4cdc19e4 4ccb4758 4ccb1fd4 4cc23cd8 400a86c0 400a913c 400a97f0 400b2250 4006f154 40077dbc 400501d8 400e14c0 400e2384

 

 

Is this routing problem?

Why this occurred? and what should i do to fix this ?

/////////////////////////////////////////////////

router static
 address-family ipv4 unicast
  20.1.2.0/24 1.1.1.4
  20.1.2.0/24 1.1.2.5
  20.1.2.0/24 1.1.3.5
  20.1.2.0/24 1.1.4.5
  20.1.2.0/24 1.1.5.5
  20.1.2.0/24 1.1.6.5
  20.1.2.0/24 1.1.7.5
  20.1.2.0/24 1.1.8.5
  20.1.2.0/24 1.1.9.5
  20.1.2.0/24 1.1.10.5
  20.1.2.0/24 1.1.11.5
  20.1.2.0/24 1.1.12.5
  20.1.2.0/24 1.1.13.5
  20.1.2.0/24 1.1.14.5
  20.1.2.0/24 1.1.15.5
  20.1.2.0/24 1.1.16.5
  20.1.2.0/24 1.1.17.5
  20.1.2.0/24 1.1.18.5
  20.1.2.0/24 1.1.19.5
  20.1.2.0/24 1.1.20.5
  192.168.10.0/24 192.168.0.1
 !
 vrf TEST_VRF
  address-family ipv4 unicast
   0.0.0.0/0 38.10.1.5
  !
 !
!
router ospf 2
 area 0
  bfd minimum-interval 200
  bfd multiplier 5
  interface TenGigE0/7/0/0
   bfd fast-detect
  !
 !
!
router ospf 100
 router-id 172.30.4.4
 network point-to-point
 microloop avoidance rib-update-delay 5000
 microloop avoidance protected
 auto-cost reference-bandwidth 100000
 redistribute connected
 redistribute static
 area 0
  fast-reroute per-prefix
  fast-reroute per-prefix remote-lfa tunnel mpls-ldp
  interface Loopback0
   passive enable
  !
  interface GigabitEthernet0/0/0/2
  !
  interface TenGigE0/0/1/0
  !
  interface TenGigE0/0/1/2
  !
  interface TenGigE0/0/1/3
  !
//////////////////////////////////////////////////////////

 

Device is ASR9K and here is the configuration. 

 

 

 

Thank you in advance : 0

 

 

 

0 Replies 0
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco