cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
656
Views
0
Helpful
5
Replies

Quick Question Regarding Software on a 7206VXR

keanej
Level 3
Level 3

Anyone know the difference between                   

The 'p' software

Like

c7200p-fpd-pkg.124-24.T7.pkg

c7200p-kboot-mz.124-24.T7.bin

c7200p-advipservicesk9-mz.124-24.T7.bin

and the software without the 'p'

c7200-boot-mz.124-24.T7.bin

c7200-kboot-mz.124-24.T7.bin

c7200-fpd-pkg.124-24.T7.pkg

It seems ours runs without the 'p' but I dont know if I should attempt to install the 'p' version.

Any Help Appreciated

James

2 Accepted Solutions

Accepted Solutions

Peter Paluch
Cisco Employee
Cisco Employee

Hi James,

I believe that the 'p' versions are intended for NPE-G2 versions of the 7200 router. If you don't have NPE-G2 in your 7200 router you probably should not try to run the 'p' version.

Do you known the Cisco Feature Navigator tool? It's a great tool to use in these cases. Visit http://cisco.com/go/fn

Best regards,

Peter

View solution in original post

Disclaimer


The   Author of this posting offers the information contained within this   posting without consideration and with the reader's understanding that   there's no implied or expressed suitability or fitness for any purpose.   Information provided is for informational purposes only and should not   be construed as rendering professional advice of any kind. Usage of  this  posting's information is solely at reader's own risk.

Liability Disclaimer

In   no event shall Author be liable for any damages whatsoever (including,   without limitation, damages for loss of use, data or profit) arising  out  of the use or inability to use the posting's information even if  Author  has been advised of the possibility of such damage.

Posting

only NPE G2 routers use 7200p image to boot.

NB: Also includes the 7201 (but not the 7301), I believe.

View solution in original post

5 Replies 5

Peter Paluch
Cisco Employee
Cisco Employee

Hi James,

I believe that the 'p' versions are intended for NPE-G2 versions of the 7200 router. If you don't have NPE-G2 in your 7200 router you probably should not try to run the 'p' version.

Do you known the Cisco Feature Navigator tool? It's a great tool to use in these cases. Visit http://cisco.com/go/fn

Best regards,

Peter

I have the NPE-G2 so I will order the 'p' versions

Thanks for the info

James

rajakalr
Cisco Employee
Cisco Employee

P as others discussed refers for NPE network processing engine -2 ie G2 which is a processor at the back of 7200

few images which are without p for 7200 router usually have G1(similar to G2 ) NPE -300,400 etc.

only NPE G2 routers use 7200p image to boot.

Disclaimer


The   Author of this posting offers the information contained within this   posting without consideration and with the reader's understanding that   there's no implied or expressed suitability or fitness for any purpose.   Information provided is for informational purposes only and should not   be construed as rendering professional advice of any kind. Usage of  this  posting's information is solely at reader's own risk.

Liability Disclaimer

In   no event shall Author be liable for any damages whatsoever (including,   without limitation, damages for loss of use, data or profit) arising  out  of the use or inability to use the posting's information even if  Author  has been advised of the possibility of such damage.

Posting

only NPE G2 routers use 7200p image to boot.

NB: Also includes the 7201 (but not the 7301), I believe.

Hello Joseph,

NB: Also includes the 7201 (but not the 7301), I believe.

Correct - the Feature Navigator claims the same.

Best regards,

Peter

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card