Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

RE: Configuration of FFTH for Cisco 1841 Router

Hello Good Day,

I need help those who success configure ffth for Cisco 1841 router

I saw the post from below link

http://unifi.athena.my/config/cisco1841.txt

I did follow it but no luck to get connected, below are my configuration

Building configuration...

Current configuration : 5138 bytes

!

version 12.4

no service pad

service tcp-keepalives-in

service tcp-keepalives-out

service timestamps debug datetime msec localtime show-timezone

service timestamps log datetime msec localtime show-timezone

service password-encryption

service sequence-numbers

!

hostname cisco1841

!

boot-start-marker

boot-end-marker

!

security authentication failure rate 3 log

security passwords min-length 6

logging buffered 51200 debugging

logging console critical

!

no aaa new-model

clock timezone PCTime 8

no ip source-route

ip cef

!

!

ip auth-proxy max-nodata-conns 3

ip admission max-nodata-conns 3

!

!

no ip bootp server

!

ip name-server 202.188.0.133

ip name-server 202.188.1.5

!

!

ip tcp synwait-time 10

ip ssh time-out 60

ip ssh authentication-retries 2

!

!

!

!

interface FastEthernet0/0

description $ETH-SW-LAUNCH$$INTF-INFO-FE 0$$ES_LAN$$FW_INSIDE$$ETH-LAN$

ip address 10.10.10.150 255.255.255.0

ip nat inside

ip virtual-reassembly

ip tcp adjust-mss 1412

duplex auto

speed auto

!

interface FastEthernet0/1

description $ETH-WAN$

no ip address

duplex auto

speed auto

pppoe enable

pppoe-client dial-pool-number 1

no cdp enable

!

interface FastEthernet0/1.500

encapsulation dot1Q 500

pppoe enable group global

no cdp enable

!

interface Dialer0

ip address negotiated

ip mtu 1492

ip nat outside

ip virtual-reassembly

encapsulation ppp

no ip mroute-cache

dialer pool 1

dialer idle-timeout 0

dialer persistent

dialer-group 1

no cdp enable

ppp authentication chap pap callin

ppp chap hostname username@unifi

ppp chap password pass123

ppp pap sent-username username@unifi password pass123

!

ip forward-protocol nd

!

ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip nat inside source list 1 interface Dialer0 overload

!

logging trap debugging

access-list 1 permit 10.10.10.0 0.0.0.255

dialer-list 1 protocol ip permit

no cdp run

!

!

control-plane

!

!

line con 0

login local

transport output telnet

line aux 0

login local

transport output telnet

line vty 0 4

privilege level 15

login local

transport input telnet ssh

line vty 5 15

privilege level 15

login local

transport input telnet ssh

!

scheduler allocate 4000 1000

end

the router need to connect the port at BTU HG850a which is belong to vlan 500

thanks

  • WAN Routing and Switching
1 REPLY
New Member

RE: Configuration of FFTH for Cisco 1841 Router

the problem solved after use "T" IOS

c1841-ipbasek9-mz.124-24.T.bin

1333
Views
0
Helpful
1
Replies