REP configuration on bridge domain

prima.ramadhan · ‎01-09-2012

Hi All,

I have read ES+ configuration guide regarding configuring REP. Its stated that we can configure REP on a bridge domain

Examples

This example shows how to configure REP over EVC using bridge-domain.

Router# enable

Router# configure terminal

Router(config)# interface gigabitEthernet 4/1

Router(config-if)# service instance 10 ethernet

Router(config-if-srv)# encapsulation dot1q 10

Router(config-if-srv)# rewrite ingress tag pop 1 symmetric

Router(config-if-srv)# bridge-domain 100

Router(config-if-srv)# exit

Router(config-if)# rep segment 2 edge

Router(config-if)# end

My question is why cant I configure this on my router:

KGD-NPE-01#sh version

Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 12.2(33)SRD4, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 22-Feb-10 01:06 by prod_rel_team

ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)

BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 12.2(33)SRD4, RELEASE SOFTWARE (fc2)

KGD-NPE-01 uptime is 1 year, 14 weeks, 3 days, 4 hours, 26 minutes

Uptime for this control processor is 1 year, 14 weeks, 3 days, 4 hours, 26 minutes

System returned to ROM by power cycle (SP by power on)

System image file is "sup-bootdisk:/c7600rsp72043-adventerprisek9-mz.122-33.SRD4.bin"

Last reload type: Normal Reload

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco CISCO7606-S (M8500) processor (revision 1.1) with 91750

Enter configuration commands, one per line. End with CNTL/Z.

KGD-NPE-01(config)#interface GigabitEthernet1/5

KGD-NPE-01(config-if)#service instance 2 ethernet

KGD-NPE-01(config-if-srv)# encapsulation dot1q 2

KGD-NPE-01(config-if-srv)# rewrite ingress tag pop 1 symmetric

KGD-NPE-01(config-if-srv)# bridge-domain 2 split-horizon

KGD-NPE-01(config-if-srv)#exit

KGD-NPE-01(config-if)#rep

KGD-NPE-01(config-if)#rep ?

% Unrecognized command

KGD-NPE-01(config-if)#rep segment 2 edge

^

% Invalid input detected at '^' marker.

KGD-NPE-01(config-if)#

Is there any software requirement for this to happen? As you can see, I am currently use SRD4.

Regards,

Prima

rsimoni · ‎01-09-2012

Hi Prima,

I can configure it on my device (with SRE4 though):

lan-7600-2(config-if)#interface GigabitEthernet7/1
lan-7600-2(config-if)#service instance 40 ethernet
lan-7600-2(config-if-srv)#encapsulation dot1q 333
lan-7600-2(config-if-srv)#rewrite ingress tag pop 1 symmetric
lan-7600-2(config-if-srv)#bridge-domain 32 split-horizon
lan-7600-2(config-if-srv)#exit
lan-7600-2(config-if)#rep ?
  block    Block port & VLANs for VLAN Load-balancing
  preempt  Preemption options
  segment  REP segment ID
  stcn     Segment Topology Change Notification

Is your module 1 an ES+? Can you print a show module please?

If yes, can you try from scratch creating a new instance with new encapsulation?

Riccardo

prima.ramadhan · ‎01-09-2012

Hi Ricardo,

Yes my module 1 is ES+ module, otherwise I can not configure EVC right? or there are other modules that can support EVC?

below is my show module:

KGD-NPE-01#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 20 7600 ES+ 7600-ES+20G3C JAE14210EWU

5 2 Route Switch Processor 720 (Active) RSP720-3C-GE JAE14190FDB

6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE JAE14190FT0

I think its because I use IOS version SRD4, while yours are using SRE4. what is your IOS train? mine is advanced IP services SSH.

Regards,

Prima

rsimoni · ‎01-10-2012

same train.

Try to create a new service instance bridging to another vlan to see if the command is available. Or else try an upgrade.

Riccardo