Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

RIP Wont send updates, timer stuck on 0

Trying to setup Rip on a 2811 so that I can route redistribute with a HP switch; problem is that the HP and the Cisco will not form a peer relationship. (EIGRP works fine)

When I debug ip rip, there are no events, packets, updates nothing, so I believe the problem is the cisco router. When I run a 'sh ip prot' the rip shows up, but the send next update timer always stays on 0, so it is never sending updates.

2811-2#sh clock

09:59:47.305 CDT Thu Jul 17 2008

#sh ip prot

Routing Protocol is "rip"

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Sending updates every 30 seconds, next due in 0 seconds

Invalid after 180 seconds, hold down 180, flushed after 240

Redistributing: eigrp 10, rip

Default version control: send version 2, receive version 2

Automatic network summarization is not in effect

Maximum path: 4

Routing for Networks:

192.186.1.0

Routing Information Sources:

Gateway Distance Last Update

Distance: (default is 120)

2811-2#sh clock

10:00:00.385 CDT Thu Jul 17 2008

#sh ip prot

Routing Protocol is "rip"

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Sending updates every 30 seconds, next due in 0 seconds

Invalid after 180 seconds, hold down 180, flushed after 240

Redistributing: eigrp 10, rip

Default version control: send version 2, receive version 2

Automatic network summarization is not in effect

Maximum path: 4

Routing for Networks:

192.186.1.0

Routing Information Sources:

Gateway Distance Last Update

Distance: (default is 120)

2811-2#sh ip int brief

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 192.168.1.1 YES NVRAM up up

2811-2#sh run int fa0/0

Building configuration...

Current configuration : 496 bytes

!

interface FastEthernet0/0

description Link to the LAN 192.168.1.0/24

ip address 192.168.1.1 255.255.255.0

no ip redirects

no ip unreachables

no ip proxy-arp

ip nat inside

ip virtual-reassembly

ip tcp adjust-mss 1452

no ip mroute-cache

duplex auto

speed auto

no mop enabled

glbp 50 ip 192.168.1.3

glbp 50 timers 5 18

glbp 50 priority 10

glbp 50 preempt delay minimum 30

glbp 50 load-balancing host-dependent

glbp 50 authentication md5 key-string 7 xxxxxxxx

end

2811-2#term mon

2811-2#debug ip rip

RIP protocol debugging is on

2811-2#sh clock

10:03:18.571 CDT Thu Jul 17 2008

2811-2#

001134: Jul 17 10:03:40.039 CDT: %SEC-6-IPACCESSLOGP: list OutsideACL denied tcp

2811-2#sh clock

10:03:59.811 CDT Thu Jul 17 2008

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)

1 ACCEPTED SOLUTION

Accepted Solutions
Silver

Re: RIP Wont send updates, timer stuck on 0

Hi,

interface FastEthernet0/0

description Link to the LAN 192.168.1.0/24

ip address 192.168.1.1 255.255.255.0

Routing for Networks:

192.186.1.0

ooops...

:-))

LR

2 REPLIES
Silver

Re: RIP Wont send updates, timer stuck on 0

Hi,

interface FastEthernet0/0

description Link to the LAN 192.168.1.0/24

ip address 192.168.1.1 255.255.255.0

Routing for Networks:

192.186.1.0

ooops...

:-))

LR

New Member

Re: RIP Wont send updates, timer stuck on 0

awwww .... fat-fingered it.

Thanks for finding my lex-dysia

484
Views
0
Helpful
2
Replies
CreatePlease to create content