Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Bronze

Ripng, and show ipv6 rip next-hops

Hi everybody

How is everybody doing ?

Please consider the following routing table:

R2#show ipv6 route

IPv6 Routing Table - 7 entries

Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP

       U - Per-user Static route, M - MIPv6

       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary

       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2

       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2

       D - EIGRP, EX - EIGRP external

C   2000::/64 [0/0]

     via ::, Serial0/0

L   2000::1:2/128 [0/0]

     via ::, Serial0/0

R   2000:1::/64 [120/2]

     via FE80::C200:FFF:FE78:0, Serial0/0

C   2001::/64 [0/0]

     via ::, Serial0/0

L   2001::2/128 [0/0]

     via ::, Serial0/0

R   4000::/64 [120/2]

     via FE80::C200:FFF:FE78:0, Serial0/0

L   FF00::/8 [0/0]

     via ::, Null0

============================================================

R2#show ipv6 rip next-hops

RIP process "zee", Next Hops

  FE80::C200:FFF:FE78:0/Serial0/0 [4 paths]

My question is why the above output shows" 4 paths" ?  I can only see two routes that were learned via next hop FE80:c200:FF"FE78:0

Thanks and have a great weekend

3 ACCEPTED SOLUTIONS

Accepted Solutions

Ripng, and show ipv6 rip next-hops

According to the command reference at:

http://www.cisco.com/en/US/docs/ios/ipv6/command/reference/ipv6_16.html#wp2669594

this would be: The number of routes in the IPv6 RIP routing table using the specified next hop

That would match exactly with your output, the only difference being that the keyword 'paths' is used instead.

Probably that is a matter of which IOS version you are using.

regards,

Leo

BTW: There is also an ipv6 related forum. Perhaps you can consider posting additional ipv6 questions there.

Cisco Employee

Ripng, and show ipv6 rip next-hops

Hi Sarah,

Can you please post the show ipv6 rip database output as well?

Best regards,

Peter

Cisco Employee

Ripng, and show ipv6 rip next-hops

Hi Sarah,

Apparently," show ipv6 rip next-hops" command gets its output from rib database not from routing table.

That's my understanding as well.

Next thing I noticed R1 advertised prefix 1111::/64  with metric 2 to R2.

But should the metric not be 1 as R1 and R2 are connected via serial interface ?

In RIPng, the metric is increased when receiving an update. This is in stern difference to previous RIP versions in which the metric was incremented when sending, and receiving routers simply accepted the metric without further incrementing it. Directly connected prefixes are advertised with initial hop count of 1 in Cisco's RIPng implementation, and after the receiving router increments the hop count by one, it yields the metric value of 2 you are seeing in your routing table.

Best regards,

Peter

4 REPLIES

Ripng, and show ipv6 rip next-hops

According to the command reference at:

http://www.cisco.com/en/US/docs/ios/ipv6/command/reference/ipv6_16.html#wp2669594

this would be: The number of routes in the IPv6 RIP routing table using the specified next hop

That would match exactly with your output, the only difference being that the keyword 'paths' is used instead.

Probably that is a matter of which IOS version you are using.

regards,

Leo

BTW: There is also an ipv6 related forum. Perhaps you can consider posting additional ipv6 questions there.

Cisco Employee

Ripng, and show ipv6 rip next-hops

Hi Sarah,

Can you please post the show ipv6 rip database output as well?

Best regards,

Peter

Bronze

Ripng, and show ipv6 rip next-hops

Hi Peter

how are you doing?

I apologize for being late; I was recreating the set-up.

R1 s0/0---2001::/64--------s0/0R2

R1's

int loopback1

1111::1/64

ipv6 rip sarah enable

Below is the outputs of various commands on R2.

R2#show ipv6 route

IPv6 Routing Table - 4 entries

R   1111::/64 [120/2]

     via FE80::C200:5FF:FE74:0, Serial0/0

C   2001::/64 [0/0]

     via ::, Serial0/0

L   2001::2/128 [0/0]

     via ::, Serial0/0

L   FF00::/8 [0/0]

     via ::, Null0

R2#show ipv6 rip next-hops

RIP process "zee", Next Hops

  FE80::C200:5FF:FE74:0/Serial0/0 [2 paths]

R2#show ipv6 rip database

RIP process "zee", local RIB

1111::/64, metric 2, installed

     Serial0/0/FE80::C200:5FF:FE74:0, expires in 159 secs

2001::/64, metric 2

     Serial0/0/FE80::C200:5FF:FE74:0, expires in 159 secs

=========================================

Apparently," show ipv6 rip next-hops" command gets its output from rib database not from routing table.

Next thing I noticed R1 advertised prefix 1111::/64  with metric 2 to R2.

But should the metric not be 1 as R1 and R2 are connected via serial interface ?

I also noticed even though R1 and R2 are connected via serial interface which is configured with 2001::/64,R1 still advertises the prefix 2001::/64 to R2.

Had R1 and R2 been configured for ipv4, R1 would not have advertised  2001:: /64 to R2.

Thanks and have a great weekend

Cisco Employee

Ripng, and show ipv6 rip next-hops

Hi Sarah,

Apparently," show ipv6 rip next-hops" command gets its output from rib database not from routing table.

That's my understanding as well.

Next thing I noticed R1 advertised prefix 1111::/64  with metric 2 to R2.

But should the metric not be 1 as R1 and R2 are connected via serial interface ?

In RIPng, the metric is increased when receiving an update. This is in stern difference to previous RIP versions in which the metric was incremented when sending, and receiving routers simply accepted the metric without further incrementing it. Directly connected prefixes are advertised with initial hop count of 1 in Cisco's RIPng implementation, and after the receiving router increments the hop count by one, it yields the metric value of 2 you are seeing in your routing table.

Best regards,

Peter

886
Views
0
Helpful
4
Replies
CreatePlease to create content