Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Rommon Problem

I have 3 cisco 3640 all have sending me rommon prompt so i tried to resolve using xmodem.

i followed the following steps:

1-Into the confreg i set the baud rate to 115200 than connect it to using HT at 115200 B/r

check the flash using dir flash:

giving the command

xmodem -c c3640-jk9o3s-mz.124-5a .bin

after the completion it give me the following error.

uncompressed image checksum is incorrect 0x46b7fabc expected a checksum of 0xa8c3facd

10 REPLIES
Silver

Re: Rommon Problem

Hi,

It looks that the image is damaged after it transfered (or it was already before that).

If you use xmodem then try to find the smallest image (you can save a lot of time) and after you can easily upgrade.

Alternatively if you have ethernet port then let's try to use tftpdnld. Very fast...

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a008015bf9e.shtml

Hope it helps, rate if does,

Krisztian

New Member

Re: Rommon Problem

hi,

I tried usinf Solarwind tftp server but when i run tftpdnld the error message is command not found.

thanks

New Member

Re: Rommon Problem

hi,

may be that command is not supporting on router. as suggested above try to upload small ios(IP) image.

New Member

Re: Rommon Problem

i tried 3mb image zip compress failed

Regards,

Silver

Re: Rommon Problem

The image should have .bin extension. First unpack it.

New Member

Re: Rommon Problem

Error-1

---------------------

rommon 1 > xmodem -yc c3640-i-mz.124-5a.bin

Do not start the sending program yet...

File size Checksum File name

3686948 bytes (0x384224) 0x107e c3640-i-mz.120-2a.t1.bin

WARNING: All existing data in flash will be lost!

Invoke this application only for disaster recovery.

Do you wish to continue? y/n [n]: y

Ready to receive file c3640-i-mz.124-5a.bin ...

Erasing flash at 0x31fc0000

program flash location 0x309a0000

Download Complete!

program load complete, entry point: 0x80008000, size: 0x9a84e8

Self decompressing the image :

Error : Uncompression of the image fail

invalid compressed data--format violated

Error : zip decompress failed

*** System received a Software forced crash ***

signal= 0x17, code= 0x7, context= 0x8000eb20

PC = 0x800080d4, Cause = 0x20, Status Reg = 0x3041f003

Error -2

------------

rommon 3 > xmodem -c c3640-jk9o3s-mz.124-5a.bin

Do not start the sending program yet...

File size Checksum File name

ROM Monitor EMT police: EMT call "EMT_TICKS" requested but not supported

28855036 bytes (0x1b84afc) 0x4a63 c3640-jk9o3s-mz.124-5a.bin (bad checksum

: 0xca98)

WARNING: All existing data in fl

Invoke this application only for disaster recovery.

Do you wish to continue? y/n [n]: y

Ready to receive file c3640-jk9o3s-mz.124-5a.bin ...

Erasing flash at 0x31fc0000

program flash location 0x31100000

amd_flash_cmd: timeout on AMD flash command

program_flash: location 0x31100000 wrote 0x6977cdde,contains 0x697726de

program flash failure at location 0x31100000 - aborting

rommon 4 >

Silver

Re: Rommon Problem

Hi,

It looks somehow the router not able to uncompress the image. What does the dir flash: shows? Is there enough space on that?

Anyway what caused to went the router to rommon?

Krisztian

Cisco Employee

Re: Rommon Problem

It seems to be a faulty hardware to me.

Please try taking the DRAM and flash out and reset them again on the slots. Power on the router and then try sending the file again. Please see the link below for placing the DRAM and Flash:

http://www.cisco.com/en/US/products/hw/routers/ps274/products_installation_guide_chapter09186a008007de1b.html#1034416

If still it doesnot work, Please get the replacement for the BOX.

-amit singh

New Member

Re: Rommon Problem

dir flash:

Device does not contain a valid magic number

boot: cannot open "flash:"

boot: cannot determine first filename on device "flash:"

Thanks

Silver

Re: Rommon Problem

Well as suspected above it might be a hardware issue indeed. Let's try to reseat the memory modules and if not helps start an RMA procedure as suggested.

Krisztian

427
Views
0
Helpful
10
Replies