Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

router (config-vpdn-req-in)#protocol pppoe (not find ) cisco 887va

i try to config adsl

i used this config

Configure ip routing, ip subnet-zero, and ip classless in order to provide flexibility in routing configuration options.

(config)#ip routing

(config)#ip subnet-zero

(config)#ip classless

Configure the global Point-to-Point Protocol over Ethernet (PPPoE) parameters.

(config)#vpdn enable

(config)#no vpdn logging

(config)#vpdn-group pppoe

(config-vpdn)#request-dialin

(config-vpdn-req-in)#protocol pppoe

(config-vpdn-req-in)#exit

(config-vpdn)#exit

Configure an IP address and subnet mask on the Cisco DSL Router Ethernet interface.

(config)#int ethernet 0

(config-if)#ip tcp adjust-mss 1452

(config-if)#ip address 41.32.58.169 255.255.255.248

(config-if)#ip nat inside

(config-if)#no shutdown

(config-if)#exit

Configure the ATM interface of your Cisco DSL Router with an ATM permanent virtual circuit (PVC), encapsulation type, and dialer pool.

(config)#int atm 0

(config-if)#pvc 0/35

(config-if-atm-vc)#pppoe-client dial-pool-number 1

(config-if-atm-vc)#no shutdown

(config-if)#exit

*******************

(config)#int dialer 1

(config-if)#mtu 1492

(config)#int dialer 1

(config-if)#mtu 1492

(config-if)#ip address 196.202.4.105 255.255.255.248

(config-if)#encapsulation ppp

********************

(config-if)#dialer pool 1

(config-if)#ppp pap sent-username 1********@tedata.net.eg password ******

(config-if)#exit

Configure a default route using Dialer1 as the outbound interface.

(config)#ip route 0.0.0.0 0.0.0.0 dialer 1

i don't find pppoe protocol red line

4 REPLIES
Cisco Employee

router (config-vpdn-req-in)#protocol pppoe (not find ) cisco 887

Hi Ahmed,

New IOSes do not use that kind of configuration. That is why you don't see the red line. Simply skip the entire VPDN section and you should be fine. The necessary PPPoE configuration is done on the PVC 0/35 - the PPPoE client is activated there, and that is all that is needed.

Best regards,

Peter

Community Member

router (config-vpdn-req-in)#protocol pppoe (not find ) cisco 887

thanks

now i don't need NAT .. the pc will take real ip 

create vlan with real ip

so the config will be

Configure ip routing, ip subnet-zero, and ip classless in order to provide flexibility in routing configuration options.

(config)#ip routing

(config)#ip subnet-zero

(config)#ip classless

i don't need that right !!!!!!!!!!!!!!!!

******************************

Configure an IP address and subnet mask on the Cisco DSL Router Ethernet interface.

(config)#int ethernet 0

(config-if)#ip tcp adjust-mss 1452

(config-if)#ip address 41.32.58.169 255.255.255.248

(config-if)#ip nat inside

(config-if)#no shutdown

(config-if)#exit

****************************

Configure the ATM interface of your Cisco DSL Router with an ATM permanent virtual circuit (PVC), encapsulation type, and dialer pool.

(config)#int atm 0

(config-if)#pvc 0/35

(config-if-atm-vc)#pppoe-client dial-pool-number 1

(config-if-atm-vc)#no shutdown

(config-if)#exit

*******************

(config)#int dialer 1

(config-if)#mtu 1492

(config)#int dialer 1

(config-if)#mtu 1492

(config-if)#ip address 196.202.4.105 255.255.255.248

(config-if)#encapsulation ppp

********************

(config-if)#dialer pool 1

(config-if)#ppp pap sent-username 1********@tedata.net.eg password ******

(config-if)#exit

Configure a default route using Dialer1 as the outbound interface.

(config)#ip route 0.0.0.0 0.0.0.0 dialer 1

interface Vlan10

ip address 196.202.4.105 255.255.255.248

*************************************************

right this config or have any mistake

Community Member

router (config-vpdn-req-in)#protocol pppoe (not find ) cisco 887

nowi have another message

when i create vlan

196.202.4.105 overlaps with dialer1

i need to make this ip  196.202.4.105 gateway to pc without nat static ip

how can i solve it

Community Member

router (config-vpdn-req-in)#protocol pppoe (not find ) cisco 887

new update

(config)#int dialer 1

(config-if)#mtu 1492

(config)#int dialer 1

(config-if)#mtu 1492

(config-if)#ip address 196.202.4.105 255.255.255.248

(config-if)#encapsulation ppp

interface Vlan10

ip address 196.202.4.105 255.255.255.248

and it's run

but when i ping in yahooo

196.202.4.105 unreachable

and in racert stop in 196.202.4.105


564
Views
0
Helpful
4
Replies
CreatePlease to create content