I have a 7200 router which reloaded couple of times last month and it always shows that router reloaded due to power-on. There was no power issue on site . Wanted to know could this be any bug.
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-JK2S-M), Version 12.1(19)E2, EARLY DEPLOYMENT RELEASE
TAC Support: http://www.cisco.com/tacCopyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Wed 30-Jul-03 04:53 by hqluong
Image text-base: 0x60008C08, data-base: 0x617FE000
ROM: System Bootstrap, Version 12.2(1r) [dchih 1r], RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE
IIRT02 uptime is 1 hour, 13 minutes
System returned to ROM by power-on
System restarted at 07:50:12 UTC Sat Sep 28 2013
System image file is "sup-slot0:/c7200-jk2s-mz.121-19.E2.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
If you require further assistance please contact us by sending email to
cisco 7206VXR (NPE300) processor (revision D) with 229376K/65536K bytes of memory.
Processor board ID 21304865
R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3 Cache
6 slot VXR midplane, Version 2.1
Last reset from power-on
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
PCI bus mb0_mb1 has 1000 bandwidth points
PCI bus mb2 has 580 bandwidth points
WARNING: PCI bus mb0_mb1 Exceeds 600 bandwidth points
5 FastEthernet/IEEE 802.3 interface(s)
31 Serial network interface(s)
2 Channelized T3 port(s)
125K bytes of non-volatile configuration memory.
46976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x102
Had faced a similar kind of issue with Cisco 7206VXR (NPE-G1) few days back. Where the local engineer said there was no problem with power as there are other devices coneected to the same power supply. While surfing i remember reading a document stating this is a known issue with IOS release 12.2 when certain modules are installed.
Check if any new module was installed,IOS upgraded/downgraded and compatibilty of the modules on the device with the existing IOS.
Question We run asr9001 with XR 6.1.3, and we have a very long delay to
login w/ SSH 1 or 2 to the device compare to IOS device. After
investigation, the there is 1s delay between the client KEXDH_INIT and
the server (XR) KEXDH_REPLY. After debug ssh serv...
Introduction The purpose of this document is to demonstrate the Open
Shortest Path First (OSPF) behavior when the V-bit (Virtual-link bit) is
present in a non-backbone area. The V-bit is signaled in Type-1 LSA only
if the router is the endpoint of one or ...
Hi, I am seeing quite a few issues with patch install and wanted to
share my experience and workaround to this. Login to admin via CLI, then
access root with the “shell” command Issue “df –h” and you’ll probably
see the following directory full or nearly ...