Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Setting up Routing for 2 networks(Should be easy)

Hi guys!

I hope someone can help me on this.

First some information about what hardware i got.

I got a Cisco Router 860VAE, i got no console cable(so i'm connected to telnet), i got a home router too(Got it from my ISP).

I'm using my router i got from my ISP to the television so i can't just remove it.. anoying..

I was getting the Cisco router because i'm studying Cisco CCNA at my school(first year) and i thought it could be cool to make NetFlow

The router i got from my ISP is not advanced at all so not many options here. Anyway it use the IP range 10.0.0.0/8

Then my CISCO router use the ip range 192.168.1.0/24

Let's go to my problem.

The problem is that i can't get connection to the internet from my computer(I know...)

Let me show my running-config(remember I'm NEW):

Current configuration : 2500 bytes

!

! Last configuration change at 18:04:48 UTC Wed Jan 15 2014 by admin

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

!

no logging buffered

enable secret 4 tnhtc92DsfdXBhelxjLWJy3243i4ntXrpb4RdfFmfqY

!

no aaa new-model

wan mode ethernet

!

!

!

ip dhcp pool ccp_pool

import all

network 192.168.1.0 255.255.255.0

dns-server 8.8.8.8 8.8.4.4

!

!

!

!

ip flow-cache timeout active 1

ip name-server 8.8.8.8

ip name-server 8.8.4.4

ip cef

no ipv6 cef

!

!

!

!

!

username admin privilege 15 secret 4 lUgFIkgcrt4SYXMq7jZtxq52lwdfgkj238

!

!

controller VDSL 0

shutdown

!

!

!

!

!

interface Loopback0

ip address 11.0.0.1 255.255.255.0

ip flow ingress

ip flow egress

!

interface Loopback1

no ip address

!

interface ATM0

no ip address

shutdown

no atm ilmi-keepalive

!

interface Ethernet0

no ip address

ip flow ingress

ip flow egress

shutdown

!

interface FastEthernet0

no ip address

!

interface FastEthernet1

no ip address

!

interface FastEthernet2

no ip address

!

interface FastEthernet3

switchport access vlan 2

no ip address

spanning-tree portfast

!

interface GigabitEthernet0

description $ETH-WAN$

ip address 10.0.0.1 255.0.0.0

ip flow ingress

ip flow egress

duplex auto

speed auto

!

interface Vlan1

ip address 192.168.1.1 255.255.255.0

ip flow ingress

ip flow egress

!

interface Vlan2

no ip address

ip flow ingress

ip flow egress

!

interface Dialer0

no ip address

ip flow ingress

ip flow egress

!

router rip

version 2

network 10.0.0.0

network 192.168.1.0

no auto-summary

!

ip default-gateway 10.0.0.100

ip forward-protocol nd

ip http server

ip http authentication local

no ip http secure-server

ip flow-capture vlan-id

ip flow-export source Vlan1

ip flow-export version 9

ip flow-export destination 192.168.1.3 9991

!

ip route 0.0.0.0 0.0.0.0 10.0.0.100

ip route 10.0.0.0 255.0.0.0 GigabitEthernet0

ip route 192.168.1.0 255.255.255.0 Vlan1

!

mac-address-table aging-time 15

!

snmp-server community public RW

snmp-server community publics RO

snmp-server ifindex persist

snmp-server enable traps config

snmp-server host 10.0.0.3 version 2c public

!

control-plane

!

banner login ^C** CISCO **^C

!

line con 0

no modem enable

line aux 0

line vty 0 4

exec-timeout 60 0

password cisco

logging synchronous

login local

transport input telnet

!

scheduler allocate 60000 1000

!

end

I've not CHANGED anything!

Some of it was just guesswork..

When i try to PING googles DNS(IP: 8.8.8.8) from the router i get

Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 36/39/40 ms

When i try to PING googles DNS from my own computer i get

Request timed out.

Request timed out.

Request timed out.

My CISCO router ip: 192.168.1.1(vlan1)        10.0.0.1(gigabitethernet/WAN)

My ISP router ip: 10.0.0.100

My computer ip: 10.0.0.3  Gateway: 10.0.0.1

Trying to make a Topology of text MY ISP -> ISP Router -> Switch -> CISCO Router -> My Computer

It's not like i can configure RIP on my ISP router so..? And BTW, my cisco router only support RIP as a routing protocol

So what do i do?

1 REPLY
Hall of Fame Super Blue

Setting up Routing for 2 networks(Should be easy)

Duplicate post, please use the link to post into the other thread -

https://supportforums.cisco.com/thread/2261524?tstart=0

Jon

207
Views
0
Helpful
1
Replies
CreatePlease to create content