In IPv4 if I type show ip route x.x.x.x I get a detailed view of the information of that route.
However I am finidng that in IPv6, when I type show ipv6 route X::X I simply get the ipv6 routing table printed out with just that one route in it.
For example:
IP version 4
R5#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
S 192.168.1.0/24 is directly connected, Null0
R5#show ip route 192.168.1.0
Routing entry for 192.168.1.0/24
Known via "static", distance 1, metric 0 (connected)
Routing Descriptor Blocks:
* directly connected, via Null0
Route metric is 0, traffic share count is 1
IP version 6
R5#show ipv6 route
IPv6 Routing Table - 10 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route, M - MIPv6
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
D - EIGRP, EX - EIGRP external
R 2004::4/128 [120/5]
via FE80::C003:14FF:FE08:0, Serial0/0
C 2005::/64 [0/0]
via ::, Loopback1
L 2005::5/128 [0/0]
via ::, Loopback1
R 2012::/64 [120/5]
via FE80::C003:14FF:FE08:0, Serial0/0
R 2013::/64 [120/5]
via FE80::C003:14FF:FE08:0, Serial0/0
R 2023::/64 [120/5]
via FE80::C003:14FF:FE08:0, Serial0/0
R 2024::/64 [120/5]
via FE80::C003:14FF:FE08:0, Serial0/0
C 2035::/64 [0/0]
via ::, Serial0/0
L 2035::5/128 [0/0]
via ::, Serial0/0
L FF00::/8 [0/0]
via ::, Null0
R5#show ipv6 route 2013::/64
IPv6 Routing Table - 10 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route, M - MIPv6
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
D - EIGRP, EX - EIGRP external
R 2013::/64 [120/5]
via FE80::C003:14FF:FE08:0, Serial0/0 <<<I'm just getting the routing table with the specified route in it
R5#
Can anyone help with this. Is it an IOS problem or am I typing in the wrong command. My Cisco book tells me that command should work.
Thanks in advance.
