Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

show processes cpu problem!

Hello all,

I have a CPU process problem, the total five minutes CPU is showed 30%. But after I sum all processes, 5Mins is only 1.74, 1Min is 2.05, and 5Secs is 3.43. It is lower than 30%. It is very confused me. What process take use the rest CPU 28% (30%-1.74%)? How to show it out?

The router platform is 7204VXR (NPE225), version Version 12.4(18). Normally the traffic is between 10Mbps to 20Mbps.

show processes cpu | exclude 0.00%__0.00%__0.00%

CPU utilization for five seconds: 34%/31%; one minute: 31%; five minutes: 30%

PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process

5 38377876 3515612 10916 0.00% 0.11% 0.06% 0 Check heaps

17 16871104 33924839 497 0.00% 0.02% 0.02% 0 EnvMon

34 14047416 48239884 291 0.00% 0.03% 0.01% 0 IP SNMP

41 314768760 33978173 9263 0.49% 0.60% 0.62% 0 Per-Second Jobs

60 343959268 914963657 375 0.49% 0.77% 0.87% 0 IP Input

66 128412 132585016 0 0.00% 0.01% 0.00% 0 SSS Feature Time

80 57476 48863899 1 0.00% 0.01% 0.00% 0 CEF process

91 119148 339104469 0 0.00% 0.04% 0.05% 0 RBSCP Background

117 2131928 35203856 60 0.00% 0.01% 0.00% 0 OSPF-100 Hello

143 316 17300 18 2.29% 0.18% 0.03% 2 Virtual Exec

146 9689108 575629 16832 0.00% 0.02% 0.00% 0 Per-minute Jobs

148 4631732 24126908 191 0.00% 0.01% 0.00% 0 PDU DISPATCHER

149 31188136 24360132 1280 0.00% 0.17% 0.08% 0 SNMP ENGINE

153 8479340 48287339 175 0.16% 0.03% 0.00% 0 OSPF-100 Router

156 17074656 2267307 7530 0.00% 0.02% 0.00% 0 BGP Scanner

Thank your

Jeffrey

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: show processes cpu problem!

Hello Jeffery,

the show cpu takes in account also cpu usage caused by interrupts:

CPU utilization for five seconds: 34%/31%; one minute: 31%; five minutes: 30%

you see 34%/31% the 31% is caused by interrupts.

if this is a software based router this can be normal and related to traffic volume.

for this reasons the sum of cpu usage caused by processes is so low in comparison to total cpu usage over time

Hope to help

Giuseppe

3 REPLIES
New Member

Re: show processes cpu problem!

I attached show process cpu log

Hall of Fame Super Silver

Re: show processes cpu problem!

Hello Jeffery,

the show cpu takes in account also cpu usage caused by interrupts:

CPU utilization for five seconds: 34%/31%; one minute: 31%; five minutes: 30%

you see 34%/31% the 31% is caused by interrupts.

if this is a software based router this can be normal and related to traffic volume.

for this reasons the sum of cpu usage caused by processes is so low in comparison to total cpu usage over time

Hope to help

Giuseppe

New Member

Re: show processes cpu problem!

Hi Giuseppe,

It is very useful for me.

Thank you

Jeffrey

177
Views
0
Helpful
3
Replies
CreatePlease to create content