Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Some error messages about ATM

Jpeg link :

http://home.so-net.net.tw/p70329/ATM.jpg

i used these commnad in cisco 2600a :

debug ip error , debug atm .

i found some error messages about atm in

cisco 2600a :

2005-08-11 00:10:41 Local7.Debug 192.168.102.251 25823: .Aug 11 00:07:39.625: IP: s=192.168.100.213 (ATM1/0), d=192.168.102.250, len 78, dispose udp.noport

2005-08-11 00:10:42 Local7.Debug 192.168.102.251 25824: .Aug 11 00:07:41.125: IP: s=192.168.100.213 (ATM1/0), d=192.168.102.250, len 78, dispose udp.noport

2005-08-11 00:10:44 Local7.Debug 192.168.102.251 25825: .Aug 11 00:07:42.625: IP: s=192.168.100.213 (ATM1/0), d=192.168.102.250, len 78, dispose udp.noport

2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25826: .Aug 11 00:55:59.564: clock change done for int ATM1/0

2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25827:

2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25828: .Aug 11 00:56:00.564: clock change removed for int ATM1/0

2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25829:

2005-08-11 02:44:10 Local7.Debug 192.168.102.251 25831: .Aug 11 02:41:06.920: ATM(ATM1/0): ATM not active yet

2005-08-11 02:44:10 Local7.Debug 192.168.102.251 25832: .Aug 11 02:41:06.920: ATM(ATM1/0): ATM not active yet

2005-08-11 02:44:10 Local7.Debug 192.168.102.251 25833: .Aug 11 02:41:06.924: ATM(ATM1/0): ATM not active yet

2005-08-11 02:44:10 Local7.Error 192.168.102.251 25834: .Aug 11 02:41:08.828: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up

2005-08-11 02:44:14 Local7.Notice 192.168.102.251 25835: .Aug 11 02:41:12.824: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down

2005-08-11 02:44:16 Local7.Notice 192.168.102.251 25836: .Aug 11 02:41:15.236: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up

2005-08-11 02:44:51 Local7.Notice 192.168.102.251 25838: .Aug 11 02:41:47.836: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down

2005-08-11 02:44:51 Local7.Error 192.168.102.251 25839: .Aug 11 02:41:48.840: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up

2005-08-11 02:44:51 Local7.Debug 192.168.102.251 25840: .Aug 11 02:41:48.840: ATMSIG: sscop open successful

2005-08-11 02:44:51 Local7.Notice 192.168.102.251 25841: .Aug 11 02:41:49.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up

2005-08-11 02:46:00 Local7.Notice 192.168.102.251 25842: .Aug 11 02:42:58.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down

2005-08-11 02:46:02 Local7.Notice 192.168.102.251 25843: .Aug 11 02:43:00.868: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up

2005-08-11 02:46:33 Local7.Notice 192.168.102.251 25844: .Aug 11 02:43:31.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down

2005-08-11 02:46:35 Local7.Notice 192.168.102.251 25845: .Aug 11 02:43:33.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up

2005-08-11 02:48:08 Local7.Notice 192.168.102.251 25847: .Aug 11 02:45:06.804: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up

2005-08-11 02:49:08 Local7.Debug 192.168.102.251 25849: .Aug 11 02:46:04.880: ATM(ATM1/0): ATM not active yet

2005-08-11 02:49:08 Local7.Error 192.168.102.251 25850: .Aug 11 02:46:05.980: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up

2005-08-11 02:49:08 Local7.Debug 192.168.102.251 25851: .Aug 11 02:46:05.980: ATMSIG: sscop open successful

  • WAN Routing and Switching
1 REPLY
New Member

Re: Some error messages about ATM

i do not found so mush error meseages in cisco 2600b

369
Views
0
Helpful
1
Replies