Jpeg link :
http://home.so-net.net.tw/p70329/ATM.jpg
i used these commnad in cisco 2600a :
debug ip error , debug atm .
i found some error messages about atm in
cisco 2600a :
2005-08-11 00:10:41 Local7.Debug 192.168.102.251 25823: .Aug 11 00:07:39.625: IP: s=192.168.100.213 (ATM1/0), d=192.168.102.250, len 78, dispose udp.noport
2005-08-11 00:10:42 Local7.Debug 192.168.102.251 25824: .Aug 11 00:07:41.125: IP: s=192.168.100.213 (ATM1/0), d=192.168.102.250, len 78, dispose udp.noport
2005-08-11 00:10:44 Local7.Debug 192.168.102.251 25825: .Aug 11 00:07:42.625: IP: s=192.168.100.213 (ATM1/0), d=192.168.102.250, len 78, dispose udp.noport
2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25826: .Aug 11 00:55:59.564: clock change done for int ATM1/0
2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25827:
2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25828: .Aug 11 00:56:00.564: clock change removed for int ATM1/0
2005-08-11 00:59:01 Local7.Debug 192.168.102.251 25829:
2005-08-11 02:44:10 Local7.Debug 192.168.102.251 25831: .Aug 11 02:41:06.920: ATM(ATM1/0): ATM not active yet
2005-08-11 02:44:10 Local7.Debug 192.168.102.251 25832: .Aug 11 02:41:06.920: ATM(ATM1/0): ATM not active yet
2005-08-11 02:44:10 Local7.Debug 192.168.102.251 25833: .Aug 11 02:41:06.924: ATM(ATM1/0): ATM not active yet
2005-08-11 02:44:10 Local7.Error 192.168.102.251 25834: .Aug 11 02:41:08.828: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up
2005-08-11 02:44:14 Local7.Notice 192.168.102.251 25835: .Aug 11 02:41:12.824: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down
2005-08-11 02:44:16 Local7.Notice 192.168.102.251 25836: .Aug 11 02:41:15.236: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up
2005-08-11 02:44:51 Local7.Notice 192.168.102.251 25838: .Aug 11 02:41:47.836: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down
2005-08-11 02:44:51 Local7.Error 192.168.102.251 25839: .Aug 11 02:41:48.840: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up
2005-08-11 02:44:51 Local7.Debug 192.168.102.251 25840: .Aug 11 02:41:48.840: ATMSIG: sscop open successful
2005-08-11 02:44:51 Local7.Notice 192.168.102.251 25841: .Aug 11 02:41:49.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up
2005-08-11 02:46:00 Local7.Notice 192.168.102.251 25842: .Aug 11 02:42:58.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down
2005-08-11 02:46:02 Local7.Notice 192.168.102.251 25843: .Aug 11 02:43:00.868: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up
2005-08-11 02:46:33 Local7.Notice 192.168.102.251 25844: .Aug 11 02:43:31.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to down
2005-08-11 02:46:35 Local7.Notice 192.168.102.251 25845: .Aug 11 02:43:33.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up
2005-08-11 02:48:08 Local7.Notice 192.168.102.251 25847: .Aug 11 02:45:06.804: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, changed state to up
2005-08-11 02:49:08 Local7.Debug 192.168.102.251 25849: .Aug 11 02:46:04.880: ATM(ATM1/0): ATM not active yet
2005-08-11 02:49:08 Local7.Error 192.168.102.251 25850: .Aug 11 02:46:05.980: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up
2005-08-11 02:49:08 Local7.Debug 192.168.102.251 25851: .Aug 11 02:46:05.980: ATMSIG: sscop open successful
