Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

span inactive

I tried config span on my 6509 switch, but somehow not actived after i configured, please check the configuration and the log:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

set vlan 1 name default type ethernet mtu 1500 said 100001 state active

set vlan 100 name vlan100 type ethernet mtu 1500 said 100100 state active

set vlan 200 name vlan200 type ethernet mtu 1500 said 100200 state active

set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active

set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee

set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm

set vlan 10

set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf off

!

#ip

set interface sl0 down

set interface sc1 down

set ip alias default 0.0.0.0

!

#ntp

set timezone GMT 8 0

!

#set boot command

set boot config-register 0x2102

set boot system flash bootflash:cat6000-sup2k8.7-6-7.bin

!

#port channel

set port channel 2/15-16 127

!

# default port status is enable

!

!

#module 1 : 2-port 1000BaseX Supervisor

set trunk 1/2 on isl 1-1005,1025-4094

!

#module 2 : 16-port 1000BaseX Ethernet

set port disable 2/2-10

set udld enable 2/7-10

set trunk 2/15 on dot1q 1-1005,1025-4094

set trunk 2/16 on dot1q 1-1005,1025-4094

set port channel 2/15-16 mode desirable non-silent

!

#module 3 empty

!

#module 4 empty

!

#module 5 empty

!

#module 6 empty

!

#module 7 empty

!

#module 8 empty

!

#module 9 : 48-port 10/100/1000BaseT Ethernet

set vlan 100 9/1,9/9-13

set vlan 200 9/4,9/47-48

set port disable 9/6-8,9/10,9/14-48

set port speed 9/1-3,9/11-14,9/47-48 100

set port speed 9/9 1000

set port duplex 9/1-3,9/11-14,9/47-48 full

set port name 9/1 outside

set port name 9/2 mangement

set port name 9/3 SGP1001

set port name 9/12 Packeteer

set port name 9/13 Span Port - NetQoS

set port flowcontrol 9/13 receive on

!

#module 15 : 1-port Multilayer Switch Feature Card

!

#module 16 empty

!

#switch port analyzer

set span 9/1 2/1 both inpkts disable learning enable multicast enable create

end

CORESW> (enable) sh span

Destination : Port 2/1

Admin Source : Port 9/1

Oper Source : None

Direction : transmit/receive

Incoming Packets: disabled

Learning : enabled

Multicast : enabled

Filter : -

Status : inactive

Total local span sessions: 1

how to make it active?

2 REPLIES

Re: span inactive

Hi Friend,

Make sure you have your source and destination port connected. Also Change the command

"set span 9/1 2/1 both inpkts disable learning enable multicast enable create " to

set span 9/1 2/1 both inpkts disable learning enable multicast enable and press enter.

This should make it work.

HTH, Please rate if it does.

-amit singh

Hall of Fame Super Silver

Re: span inactive

I think that Amit is on the right track when he comments about the source and destination ports. It would be helpful to see the output of show port 2/1 and show port 9/1. I suspect that one (or perhaps both) of the ports is not active.

HTH

Rick

134
Views
5
Helpful
2
Replies