Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

SUP720 in VSS LED status

Hi,

The LED status on SUP 720 in VSS  is different for IOS SXH and SXI ?????????

i had configured VSS on IOS SXI4a the standby SUP SYSTEM LED is amber,when i pull down the active switch the standby comes up and the amber changes to green.VSS working fine no issues.

BUT

Also i had configured VSS on IOS SXH8a, the STANDBY SUP all LED's are green including the SYSTEM. But the VSS is working fine no issues, Is this is normal or any missing configuration.

Thanks.

2 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

Re: SUP720 in VSS LED status

Hello Jack,

The VSS Standby "Active" LED should be Amber / Orange (to indicate that it is NOT the Active Supervisor):

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Module_Installation/Sup_Eng_Guide/02superv.html#wp1080351

The active led you see on SXI image is correct. The sup on the active switch should be green and on the standby, it should be amber.

There is a software issue with the led in SXH release. Basically, the LED on the sup does not show the correct status.

Refer Bug ID : CSCso72250

In both the cases, the performance of the VSS is unaffected its just the LED status change between two codes.

Thanks,

Ricky Micky

* Rate useful posts

Cisco Employee

SUP720 in VSS LED status

Hello Jack,

There are multiple ways to search bug in system.

1) You can search in the release notes for the specific IOS train and look for open caveats.

2) Try searching for the bug in the below tool,

http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs

and if you are interested in certain topic or certain bug try subscribing to it so that you will receive frequent updates as the bug progress. Below link for registration

http://www.cisco.com/cisco/support/notifications/addedit.html

Thanks,

Ricky Micky

*Rate useful posts

4 REPLIES
Cisco Employee

Re: SUP720 in VSS LED status

Hello Jack,

The VSS Standby "Active" LED should be Amber / Orange (to indicate that it is NOT the Active Supervisor):

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Module_Installation/Sup_Eng_Guide/02superv.html#wp1080351

The active led you see on SXI image is correct. The sup on the active switch should be green and on the standby, it should be amber.

There is a software issue with the led in SXH release. Basically, the LED on the sup does not show the correct status.

Refer Bug ID : CSCso72250

In both the cases, the performance of the VSS is unaffected its just the LED status change between two codes.

Thanks,

Ricky Micky

* Rate useful posts

Community Member

SUP720 in VSS LED status

Tx Richard,

How we will come to know the BUGs, Can u route me to the page where cisco places all information of bugs for IOS and devices.

Tx

Cisco Employee

SUP720 in VSS LED status

Hello Jack,

There are multiple ways to search bug in system.

1) You can search in the release notes for the specific IOS train and look for open caveats.

2) Try searching for the bug in the below tool,

http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs

and if you are interested in certain topic or certain bug try subscribing to it so that you will receive frequent updates as the bug progress. Below link for registration

http://www.cisco.com/cisco/support/notifications/addedit.html

Thanks,

Ricky Micky

*Rate useful posts

Community Member

SUP720 in VSS LED status

tx,

Hope to see u again in next post.

1719
Views
0
Helpful
4
Replies
CreatePlease to create content