TCP/IP - X25

[denaumcisco]

Good morning Folks,

I have this situation

PC1 -> router A - router B -> pc2

where:

PC1=192.168.1.1

router A (eth)=192.168.1.100

router A (serial) = x25 123

router B (serial) = x25 789

router B (eth) = 192.168.2.100

PC2= 192.168.2.1

Now I can use a "translate" and start a telnet session from pc1 to router B, but what I need is start a telnet session from pc1 to pc2.

What I have to do? a translate on route B? How?

Thanks

[andrew.prince]

Have a look at the below:-

http://www.cisco.com/en/US/tech/tk713/tk730/technologies_configuration_example09186a0080093c0e.shtml

HTH>

[denaumcisco]

I need TCP over X25.

About the file attached, I can connect from PC A to router B, and I can connect from router A to PC B, but I can't connect from pc A to pc B. (I'm using apache for this test)

that is my routers configurations:

show conf

Using 891 out of 245752 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

!

no aaa new-model

!

resource policy

!

ip subnet-zero

!

!

ip cef

!

!

!

x25 routing

!

!

!

interface FastEthernet0/0

ip address 192.168.1.100 255.255.255.0

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface Serial0/0/0

no ip address

encapsulation x25 dce

no ip mroute-cache

x25 address 123

!

interface Serial0/0/1

no ip address

shutdown

clock rate 125000

!

ip classless

!

ip http server

!

!

translate x25 123 tcp 192.168.1.1 port 8080

access-list 100 permit icmp any any

access-list 100 permit tcp any any

x25 route 789 interface Serial0/0/0

!

control-plane

!

!

line con 0

line aux 0

line vty 0 4

login

!

scheduler allocate 20000 1000

!

end

Router#

and the another router:

show conf

Using 891 out of 245752 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

!

no aaa new-model

!

resource policy

!

ip subnet-zero

!

!

ip cef

!

!

x25 routing

!

!

!

interface FastEthernet0/0

ip address 192.168.0.100 255.255.255.0

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface Serial0/0/0

no ip address

encapsulation x25 dce

no ip mroute-cache

x25 address 789

!

interface Serial0/0/1

shutdown

clock rate 125000

!

ip classless

!

ip http server

!

!

translate x25 123 tcp 192.168.1.1 port 8080

access-list 100 permit icmp any any

access-list 100 permit tcp any any

x25 route 789 interface Serial0/0/0

!

control-plane

!

!

line con 0

line aux 0

line vty 0 4

login

!

scheduler allocate 20000 1000

end

Router#

[denaumcisco]

anyone?

[denaumcisco]

I got it!, but when I open my page it came with tcp header too, not the correct page.

Is it a problem of encapsulation? How can I resolve this?

[ohassairi]

here is an example to route TCP/IP over x25 network:

!

interface Ethernet0

ip address 194.147.160.254 255.255.255.0

!

interface Serial0

ip address 192.1.1.1 255.255.255.0

encapsulation x25

x25 address 133014389

x25 htc 2

x25 idle 1

x25 nvc 2

x25 map ip 192.1.1.2 112010132

(remote wan) (remote x25)

!

ip route 193.1.1.0 255.255.255.0 192.1.1.2