Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

TFTP configuration on a 2811 router

hi,

happy new year every one,

i have a bunch of 2811 routers in my lab, and i am trying make one of my 2811 router to act as a tftp server, i have copied the required files and enable tftp on the flash but i am not able to copy the files to my other routers using tftp,

any help will be vreatly appreciated,

thanking you,

som

16 REPLIES
New Member

Re: TFTP configuration on a 2811 router

Hi Somesh,

Are they the same Model ?

DAK

New Member

Re: TFTP configuration on a 2811 router

Check their memory and capacity

New Member

Re: TFTP configuration on a 2811 router

yes all of them are same series router and the memory space is more than enough, when i try to do it says source file r dirctory not found but where as it exists in the tftp.

after trying different options i found its copying 1 file from the same directory but not the other file

and you please help me how to write back to the tftp it says access denied

Hall of Fame Super Silver

Re: TFTP configuration on a 2811 router

Somesh

What files are you attempting to copy using the router as the tftp server? The implementation of tftp in IOS is not a full function tftp server. It will copy image files and config files but not other types of files (at least that was true the last time I tested it).

I am not clear what you mean when you say:"help me how to write back to the tftp it says access denied". Perhaps you can clarify what is the issue and then perhaps we can make better suggestions about it.

HTH

Rick

New Member

Re: TFTP configuration on a 2811 router

hi rick,

i am trying to establish a topology where i can copy the configuration files from the tftp server to the existing routers my topology and vice versa i.e. copying the routers configuration to the tftp.

Hall of Fame Super Silver

Re: TFTP configuration on a 2811 router

Somesh

You have described the problem in general terms. Perhaps you could post the specifics of how you have configured the router as tftp server, and specifics of the commands you are using to try to copy the files, and specifics of the error messages. If we had that perhaps we could understand what is the problem.

HTH

Rick

New Member

Re: TFTP configuration on a 2811 router

hi Rick,

i have attached my lab topology, i am trying to copy the configuration from access routers and switches to my tftp server, i can ping the tftp server. the error is:

AR2#copy tftp: flash:

Address or name of remote host [10.9.9.1]?

Source filename [tftp/i1-routerx-4-6-end]? flash:/tftp/i1-routerx-4-6-end

Destination filename [i1-routerx-4-6-end]?

Accessing tftp://10.9.9.1/flash:/tftp/i1-routerx-4-6-end...

%Error opening tftp://10.9.9.1/flash:/tftp/i1-routerx-4-6-end (No such file or directory)

on the tftp router i get the following notification:

TFTP#

*Jan 8 11:11:12.990: TFTP: Server request for port 50264, socket_id 0x44F4F384 for process 33

*Jan 8 11:11:12.990: TFTP: read request from host 10.9.9.3(50264) via FastEthernet0/0.38

*Jan 8 11:11:12.990: TFTP: Looking for tftp/i1-routerx-4-6-end

*Jan 8 11:11:12.990: TFTP: Sending error 1 No such file

*Jan 8 11:11:26.930: TFTP: Server request for port 53004, socket_id 0x44F4F384 for process 33

*Jan 8 11:11:26.930: TFTP: read request from host 10.9.9.3(53004) via FastEthernet0/0.38

*Jan 8 11:11:26.930: TFTP: Looking for flash:/tftp/i1-routerx-4-6-end

*Jan 8 11:11:26.930: TFTP: Sending error 1 No such file

TFTP#

the output of my flash memory:

TFTP#sh flash

-#- --length-- -----date/time------ path

1 38154344 Jan 5 2009 06:38:48 +00:00 c2800nm-advipservicesk9-mz.124-23.bin

2 0 Jan 8 2009 08:57:38 +00:00 tftp

3 1562 Jan 8 2009 09:12:28 +00:00 tftp/switch1-confg

4 869 Jan 8 2009 10:26:14 +00:00 tftp/i1-routerx-4-6-end

25845760 bytes available (38170624 bytes used)

i am able to copy switch1-config to my devices but not the i1-routerx-4.....

and same way i cannot copy any file to the tftp from my devices.

New Member

Re: TFTP configuration on a 2811 router

hi rick ,

i have added my flash content also in this attachment please check it

thanking you for ur concern to help me,

Re: TFTP configuration on a 2811 router

Somesh,

Make sure you have the following commands in your TFTP server router config.

tftp-server flash:tftp/switch1-confg

and

tftp-server flash:tftp/i1-routerx-4-6-end

If this doesn't help please post the TFTP server router's config.

HTH,

Mark

Also: here a guide that may help.

http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note09186a00800a6744.shtml#copying_one_router

New Member

Re: TFTP configuration on a 2811 router

hi mark,

i have already configured those commands on my router,

New Member

Re: TFTP configuration on a 2811 router

It seems source file and destination file are the same.

Since this is lab topology, i think you can connect them directly and let them be in the same network.

HTH

DAK

Hall of Fame Super Silver

Re: TFTP configuration on a 2811 router

Somesh

I believe that you are running into the restriction that I mentioned in my original post. The implementation of TFTP in IOS is limited. It will process copy of image files and config files, but not other file types. I suggest that you rename this file: tftp/i1-routerx-4-6-end and name it tftp/i1-routerx-4-6-confg and try the copy with the new name. Give it a try and let us know the results.

HTH

Rick

New Member

Re: TFTP configuration on a 2811 router

hello rick,

yes what u said was correct the tftp server on IOS is limited it worked after i changed the file name to tftp/i1-routerx-4-6-end-confg.

its working when i copy from tftp to my routers but even now i cannot copy vice versa, i.e. cannot copy the router AR2 config to the tftp server it says permission denied.

the output at router ar2:

AR2#copy run tftp

Address or name of remote host []? 10.9.9.1

Destination filename [ar2-confg]?

TFTP: error code 2 received - 16739

%Error opening tftp://10.9.9.1/ar2-confg (Permission denied)

AR2#

error notification on my tftp server:

TFTP(config)#

*Jan 9 06:31:08.185: TFTP: Server request for port 53074, socket_id 0x44F4F384 for process 33

*Jan 9 06:31:08.185: TFTP: write request from host 10.9.9.3(53074) via FastEthernet0/0.38

*Jan 9 06:31:08.185: TFTP: Sending error 2 Access denied

TFTP(config)#

New Member

Re: TFTP configuration on a 2811 router

Hi Somesh

do you check for capacity flash?

Hall of Fame Super Silver

Re: TFTP configuration on a 2811 router

Somesh

I am glad that you are making progress in getting the TFTP to work and in understanding the limitations of the implementation of TFTP in IOS. I believe that it will be easier to accomplish what you are trying to do if you get some device other than your router to function as your TFTP server. There are many implementations of TFTP that could work for you and some of them are free software.

HTH

Rick

New Member

Re: TFTP configuration on a 2811 router

hi rick,

i thank you very much for all your help, i am planning to get a seperate device to act as a tftp server, but for the timebeing may be for 2 - 3 months i have to make it work with the router,

still on ething is not cleared,

can't i write back to the tftp server.

2900
Views
0
Helpful
16
Replies