Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

un-readable code in show log

Hi, Any Cisco TAC engineer there?

I got this un-readable code in SHOW LOG. any idea?

=======================

ROUTER-B4# sh log

Syslog logging: enabled (9 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns)

Console logging: disabled

Monitor logging: level debugging, 0 messages logged

Buffer logging: level debugging, 33391 messages logged

Logging Exception size (4096 bytes)

Count and timestamp logging messages: disabled

Persistent logging: disabled

Trap logging: level debugging, 823194 message lines logged

Logging to 210.55.176.20, 823194 message lines logged

Logging to 202.27.185.70, 823194 message lines logged

Logging to 202.27.185.129, 823194 message lines logged

Logging to 210.54.50.2, 823148 message lines logged

Logging to 210.54.50.34, 823148 message lines logged

Logging to 203.96.127.2, 821762 message lines logged

Log Buffer (100000 bytes):

FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 002D 0104 12A2 00B4 D230 0C44 1002 0601 0400 0100 0102 0280 0002 0202 00

ROUTER-B4#

=============================================================

ROUTER-B4#sh ver

Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(26)S2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2004 by cisco Systems, Inc.

Compiled Fri 09-Apr-04 01:23 by nmasa

Image text-base: 0x40010E80, data-base: 0x41304000

ROM: System Bootstrap, Version 11.1(8)CA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

BOOTLDR: RSP Software (RSP-BOOT-M), Version 12.0(19)S1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

ROUTER-B4 uptime is 2 years, 33 weeks, 1 day, 7 hours, 34 minutes

System returned to ROM by reload at 06:15:09 nzst Sun Apr 25 2004

System restarted at 06:17:01 nzst Sun Apr 25 2004

System image file is "slot0:rsp-k4pv-mz.120-26.S2.bin"

cisco RSP4 (R5000) processor with 163840K/2072K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

G.703/E1 software, Version 1.0.

G.703/JT2 software, Version 1.0.

X.25 software, Version 3.0.0.

Chassis Interface.

1 VIP2 R5K controller (2 FastEthernet).

1 FEIP controller (1 FastEthernet).

3 FastEthernet/IEEE 802.3 interface(s)

123K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

20480K bytes of Flash PCMCIA card at slot 1 (Sector size 128K).

8192K bytes of Flash internal SIMM (Sector size 256K).

No slave installed in slot 3.

Configuration register is 0x102

ROUTER-B4#

2 REPLIES

Re: un-readable code in show log

clear log once and see if you are getting those characters again in your logs.

New Member

Re: un-readable code in show log

I did "clear log". But still got the same unreadeble message in the log.

150
Views
0
Helpful
2
Replies
CreatePlease to create content