Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

VWIC2-2MFT-T1/E1 ethernet card

I have a VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on cisco router 2801. what interface to setup for this card?

  • WAN Routing and Switching
18 REPLIES
Hall of Fame Super Gold

Re: VWIC2-2MFT-T1/E1 ethernet card

That is not an ethernet card, it is a WAN or Voice T1/E1 card. What do you need to do ?

Re: VWIC2-2MFT-T1/E1 ethernet card

first of all you need select a type T1 or E1

card type {t1 | e1} slot [bay]

http://www.cisco.com/en/US/docs/ios/12_3/vvf_r/vrg_c2_ps1839_TSD_Products_Command_Reference_Chapter.html#wp1124401

after that you will get in the configuration T1 or E1 controller.

Re: VWIC2-2MFT-T1/E1 ethernet card

it got two ethernet port. need combine them as a single E1 circuit

WIC/VIC/HWIC Slot 1:

VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1

Hardware Revision : 0.0

Top Assy. Part Number : 800-22629-05

Board Revision : B0

Deviation Number : 95966

Fab Version : 04

PCB Serial Number : FOC12220LH6

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VWIC2-2MFT-T1/E1

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 FC 41 00 00 C0 46 03 20 00 58 65 05

0x10: 42 42 30 88 00 01 76 DE 02 04 C1 8B 46 4F 43 31

0x20: 32 32 32 30 4C 48 36 03 00 81 00 00 00 00 04 00

0x30: CB 90 56 57 49 43 32 2D 32 4D 46 54 2D 54 31 2F

0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Hall of Fame Super Gold

Re: VWIC2-2MFT-T1/E1 ethernet card

Hi, ethernet is the LAN thing, the connector with 8 pins is called RJ-45 and sometime RJ-48.

Do you have the circuit active and delivered already ?

Re: VWIC2-2MFT-T1/E1 ethernet card

yes circuit is active connected to a MUX. just need to setup the VWIC card on the router and combine both E1's as a single circuit

Hall of Fame Super Gold

Re: VWIC2-2MFT-T1/E1 ethernet card

card type E1

network-clock-participate wic

network-clock-select 1 E1 /0

network-clock-select 2 E1 /1

controller E1 0//0

channel-group 0 timeslots 1-31

controller E1 0//1

channel-group 0 timeslots 1-31

The serial interfaces will appear, configure as usual with DEFAULTS, I recommend that initially you do NOT use multilink PPP to test the circuit first, after that you can look into "combining".

Re: VWIC2-2MFT-T1/E1 ethernet card

i only have one card in slot 1

Hall of Fame Super Gold

Re: VWIC2-2MFT-T1/E1 ethernet card

Then replace with 1 and enter the commands above.

As an appreciation for those providing answers, please rate useful posts with the scrollbox below!

Re: VWIC2-2MFT-T1/E1 ethernet card

paolo,

i now have

controller E1 0/1/0

channel-group 0 timeslots 1-31

!

controller E1 0/1/1

channel-group 0 timeslots 1-31

!

!

interface Serial0/1/0:0

no ip address

!

interface Serial0/1/1:0

no ip address

i gues i need to use multilink ppp to combine both serial sub interfaces right?

1555
Views
52
Helpful
18
Replies
This widget could not be displayed.