When I connect using my mobile via AP, i will get the ADSL speed 40mb in speedtest.net, but when I connect my laptop same AP, i will get leaseline speed of 4mb. Both configured with no proxy, Both gets the same Public IP from ADSL. All LAN http speed also is 4mb with ADSL public ip when testing in speedtest.net My configuration below.
! interface GigabitEthernet0/0.5 description SERVERSNETWORK encapsulation dot1Q 5 ip address 192.168.5.1 255.255.255.0 ip helper-address 192.168.5.11 ip nbar protocol-discovery ip nat inside ip virtual-reassembly in ip policy route-map REROUTE-HTTP ! interface GigabitEthernet0/0.70 description NATIVE encapsulation dot1Q 70 native ip address 192.168.70.1 255.255.255.0 ip helper-address 192.168.5.11 ip nbar protocol-discovery ip nat inside ip virtual-reassembly in ip policy route-map REROUTE-HTTP ! interface GigabitEthernet0/1 description MAIN ip address 213.42.34.abc 255.255.255.abc ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface FastEthernet0/1/0 description ADSL no ip address ip flow egress ip virtual-reassembly in duplex auto speed auto pppoe enable group global pppoe-client dial-pool-number 10 no cdp enable ! interface FastEthernet0/1/1 description BACKUP ip address 213.42.68.abc 255.255.255.abc ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/0/0 no ip address ! interface GigabitEthernet0/0/1 no ip address ! interface GigabitEthernet0/0/2 no ip address ! interface GigabitEthernet0/0/3 description MAIN switchport access vlan 50 no ip address ! interface Vlan1 no ip address ! interface Vlan50 ip address 83.111.165.abc 255.255.255.abc ip flow ingress ! interface Dialer1 ip address negotiated ip mtu 1492 ip nat outside ip virtual-reassembly in max-fragments 64 max-reassemblies 512 encapsulation ppp ip tcp adjust-mss 1452 dialer pool 10 ppp authentication pap callin ppp pap sent-username abcde password 7 abcde ppp ipcp dns request accept ppp ipcp address accept no cdp enable ! ! router bgp 65200 bgp log-neighbor-changes network 83.111.165.abc mask 255.255.255.abc network 94.56.22.abc mask 255.255.255.abc neighbor 213.42.34.abc remote-as 5300 neighbor 213.42.34.abc update-source GigabitEthernet0/1 neighbor 213.42.34.abc route-map MAINLL in neighbor 213.42.68.abc remote-as 5300 neighbor 213.42.68.abc update-source FastEthernet0/1/1 neighbor 213.42.68.abc route-map BACKUPLL in maximum-paths 2 ! ip forward-protocol nd ! ip http server ip http authentication local ip http secure-server ! ip dns server ip nat inside source route-map ADSL interface Dialer1 overload ip nat inside source route-map BACKUP interface FastEthernet0/1/1 overload ip nat inside source route-map MAIN interface GigabitEthernet0/1 overload !
ip access-list extended COMMON-TRAFFIC deny tcp any any eq www deny tcp any any eq 443 permit ip any any ip access-list extended HTTP-TRAFFIC permit tcp any any eq www permit tcp any any eq 443 deny ip any any ! ! route-map ADSL permit 10 match ip address HTTP-TRAFFIC match interface Dialer1 ! route-map MAIN permit 10 match ip address COMMON-TRAFFIC match interface GigabitEthernet0/1 ! route-map BACKUP permit 10 match ip address COMMON-TRAFFIC match interface FastEthernet0/1/1 ! route-map MAINLL permit 10 set local-preference 110 ! route-map BACKUPLL permit 10 set local-preference 90 !
route-map REROUTE-HTTP permit 10 match ip address HTTP-TRAFFIC set interface Dialer1 ! ! !
Hi everyone, I would like to thank you in advance for any help you can provide a newcomer like myself!
Im studying the 100-105 book by Odom and am currently on the topic of Port security. I purchased a used 2960 and I'm trying to follow a...
While deploying a number of 18xx/2802/3802 model access points (APs), which run AP-COS as their operating platform. It can be observed on some occasions that while many of their access points were able to join the fabric WLC withou...
I am going to design and build an LAN network under a tunnel underground with long distance between the switches.
I will have 2 Catalyst switches and 8 Industrial IE3000, and they will be connected with fiber.
For now I am planning on use Layer-2 s...