Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

When install SDM into router 7206, it´s rebooting.

Hi,

I have a cisco router 7206VXR with IOS Version 12.3(6) c7200-a3jk9s-mz.123-6.bin. When I install the SDM software version 22 to the router, it´s rebotting.

Help me please.

Thank you in advance.

Wmatta

5 REPLIES
New Member

Re: When install SDM into router 7206, it´s rebooting.

Is the router continously rebooting? Did the router meet the minimum system requirements before you put the Sdm software on the router? The following link might help: http://www.cisco.com/en/US/products/hw/routers/ps341/products_tech_note09186a00804084c9.shtml#Solution2

If this post helped please rate my post,thanks.

New Member

Re: When install SDM into router 7206, it´s rebooting.

Hi,

The router is reboting, when i installed the SDM software. After reboot the router is working fine. But i didn´t install the SDM software. I send the "show version" this router in next post.

Thanks,

Wmatta

Cisco Employee

Re: When install SDM into router 7206, it´s rebooting.

Hi,

How did you install SDM on the router? Through the SDM installation wizard?? Or do you manually copied the SDM files to the router?

Can you please send us the output of "show version"

Thanks,

Ravikumar

New Member

Re: When install SDM into router 7206, it´s rebooting.

Hi,

Yes, I installed through SDM instalation wizard.

# Show Version

IOS (tm) 7200 Software (C7200-A3JK9S-M), Version 12.3(6), RELEASE SOFTWARE (fc3)

Copyright (c) 1986-2004 by cisco Systems, Inc.

Compiled Wed 11-Feb-04 15:57 by kellythw

Image text-base: 0x60008AF4, data-base: 0x622F8000

ROM: System Bootstrap, Version 12.2(4r)B2, RELEASE SOFTWARE (fc2)

BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.1(14)E6, EARLY DEPLOYMENT REL

EASE SOFTWARE (fc1)

RTR3_GRAVAMES uptime is 8 weeks, 6 days, 9 minutes

System returned to ROM by power-on

System image file is "disk1:c7200-a3jk9s-mz.123-6.bin"

cisco 7206VXR (NPE400) processor (revision A) with 229376K/32768K bytes of memor

y.

Processor board ID 31414097

R7000 CPU at 350MHz, Implementation 39, Rev 3.3, 256KB L2 Cache

6 slot VXR midplane, Version 2.7

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

TN3270 Emulation software.

PCI bus mb0_mb1 has 400 bandwidth points

PCI bus mb2 has 0 bandwidth points

2 FastEthernet/IEEE 802.3 interface(s)

40 Serial network interface(s)

125K bytes of non-volatile configuration memory.

47040K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).

125440K bytes of ATA PCMCIA card at slot 1 (Sector size 512 bytes).

8192K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x2102

Thanks,

Wmatta

Cisco Employee

Re: When install SDM into router 7206, it´s rebooting.

Hi,

Are you facing this problem when you install SDM on disk1?

Are you sure the IOS is the first file in disk1? If not, you can configure necessary "boot system" command to make the router boot from this IOS image.

Other solution is to install SDM on your PC.

Thanks,

Ravikumar

343
Views
0
Helpful
5
Replies
CreatePlease to create content