Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

WIC-1DSU-T1-V2

I have a C2621 and trying to install a T1 card.

It does not show any servivce-module or controller commands.

The software version in good when compared to the requirements guide.

How do I configure the card in the router for T1?

6 REPLIES
New Member

WIC-1DSU-T1-V2

The single port T1 cards require no configuration.

Hall of Fame Super Silver

WIC-1DSU-T1-V2

Arthur

Perhaps we could provide better answers if we had more information to work with. As a start can you provide the specifics about what T1 card you are trying to install? And can you provide the specifics of the version of code that you are running? Can you post the output of show version so that we can see if the card shows up?

HTH

Rick

Hall of Fame Super Silver

WIC-1DSU-T1-V2

Arthur

I have done some checking about the WIC-1DSU-T1-V2 and I find this in an document about the card:

The Cisco T1 DSU/CSU -V2 WIC is supported on the Cisco 1700 Series,       2600XM Series, 3631, and 3700 Series routers, and Cisco ICS 7750       software.

see this URL for additional details

http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a0080093d70.shtml

So can you tell us whether your router is a 2600 or a 2600XM?

HTH

Rick

New Member

Re: WIC-1DSU-T1-V2

Good morning Richard

Thank you for looking at this

My Router is an C2621 and I cannot find any thing that suggests its a C2600XM.

When I try to show devices I cannot see the card.

I attached a print out of my IOS.

show version

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-IK9O3S3-M), Version 12.3(3), RELEASE

SOFTWARE (fc2)

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Tue 19-Aug-03 16:32 by dchih

Image text-base: 0x80008098, data-base: 0x819AF6CC

ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)

System returned to ROM by power-on

System image file is "flash:c2600-ik9o3s3-mz.123-3.bin"

cisco 2621 (MPC860) processor (revision 0x600) with 56320K/9216K bytes

of memory.

Processor board ID JAD054906Z3 (651052972)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

GATEWAY(config)#int fa0/0

GATEWAY(config-if)#exit

GATEWAY(config)#int s0/0

^

% Invalid input detected at '^' marker.

GATEWAY(config)#int s0/0/0

^

% Invalid input detected at '^' marker.

GATEWAY(config)#int serial0/0

^

% Invalid input detected at '^' marker.

Hall of Fame Super Silver

WIC-1DSU-T1-V2

Arthur

Thank you for the additional information. The show version seems to indicate that your router is 2621 and not an XM. And if the information in the URL is accurate then this card is only supported in the XM version of the routers. So it looks like the card and your router are not compatible.

HTH

Rick

New Member

Re: WIC-1DSU-T1-V2

Richard

Thank you for the input

After reading several documents online, I thought it would be good to

get another opinion. Some papers indicated it may work and others said

no.

Thank you

Arthur

499
Views
0
Helpful
6
Replies
CreatePlease login to create content