Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

unable to find reduction traffic on wave 694 and finding host flapping on switch which is connected to the wave.

Hi Team

I was stuck in a issue with cisco wave-694.

4506 ==========================Wave-694

4506   ( Gi4/40, Gi4/41 )  are in port channel has connected to Wave-694. which is in production suddenly am finding Host flapping on both interfaces

00:06:51: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:52: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:54: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:56: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:06:58: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:00: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:02: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:04: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:06: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

00:07:08: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/40 and port Gi4/41

in wave-694

aa.png

here we are unable to find reduction %  traffic.

Please  let us know how to overcome this..  and send me a doc for troubleshooting WAAS device.

Appriciate your response as early possiable.

2 REPLIES

Re: unable to find reduction traffic on wave 694 and finding hos

Hi,

Can you set any one of interface as primary in 694 device and assign it to standby inerface  group.

ex:

interface Standby 1

ip address XXXX

exit

!

interface GigabitEthernet 1/0

standby 1 primary

exit

interface GigabitEthernet 2/0

standby 1

exit

Regards,

Bala

New Member

unable to find reduction traffic on wave 694 and finding host fl

Hi Team

we are unable to find optimizing traffic and reduction traffic in cisco wave-694, it is in production suddently its not showing. am new for this box, can you please guide me some commands, so i can  copy here for furthere troubleshoot.

sh version

Cisco Wide Area Application Services Software (WAAS)

Copyright (c) 1999-2013 by Cisco Systems, Inc.

Cisco Wide Area Application Services (universal-k9) Software Release 5.0.3c (build b7 Feb  8 2013)

Version: oe694-5.0.3c.7

if there is any bugs also please let me know, please take this in high priritoy  and help me out on this.

111.png

Thanks in advance.

Naga

349
Views
5
Helpful
2
Replies