12-18-2013 11:04 AM
Hello,
I am working on replacing WAE-512-K9 (running code oe512-4.4.5.5) with a newer WAVE-694-K9 ( running code oe694-5.1.1.16). During this process I am duplicating the config from the old to the new and am running into difficulty getting some of the commands to copy due to the new WAVE-694-K9 not accepting these commands:
wccp router-list 1 X.X.X.X
wccp tcp-promiscuous service-pair 61 62 failure-detection 30
wccp tcp-promiscuous service-pair 61 62 router-list-num 1
wccp version 2
waas01(config)#wccp router-list 1 X.X.255.25
wccp tcp-promiscuous service-pair 61 62 ^
% Invalid input detected at '^' marker.
waas01(config)#wccp tcp-promiscuous service-pair 61 62 failure-detection 30
^
% Invalid input detected at '^' marker.
waas01(config)#wccp tcp-promiscuous service-pair 61 62 router-list-num 1
^
% Invalid input detected at '^' marker.
waas01(config)#wccp version 2
^
% Invalid input detected at '^' marker.
Can someone let me know what, if any, are the equivalent commands would be on the newer WAVE-694-K9 for the above commands?
Thank you,
Adil
Solved! Go to Solution.
12-22-2013 09:24 PM
Hi,
In new WAAS IOS code to enable the WCCP first you need to activate the interception method as WCCP.
conf t
interception-method wccp
12-18-2013 01:36 PM
Hi Adil,
Can you check what is the device mode configured using the command: show device-mode current?
I suspect that device mode is not application-accelerator and that's why those commands are not working.
Can you please check that and correct it if that is the case and then try again.
Let me know how it goes.
Regards,
Kanwal
12-19-2013 06:20 PM
I had shipped out the unit before receiving this reply. I will run the command once I have it connected to the network. Thank you!
Sent from Cisco Technical Support iPad App
12-19-2013 06:22 PM
Hi Adil,
Sure. Let me know how it goes.
Regards,
Kanwal
Sent from Cisco Technical Support iPhone App
12-22-2013 09:24 PM
Hi,
In new WAAS IOS code to enable the WCCP first you need to activate the interception method as WCCP.
conf t
interception-method wccp
01-14-2014 12:47 PM
Hi Balakrishnan,
You are correct. After entering this command, then it started accepting the wccp commands. One more questions is what is the command the WAE is looking for by the message, "Router list has been added. Please enable service."
waas01(config)#interception-method wccp
waas01(config)#wccp router-list 1 172.30.255.25
waas01(config)#wccp tcp-promiscuous service-pair 61 62 failure-detection 30
waas01(config)#wccp tcp-promiscuous service-pair 61 62 router-list-num 1
Router list has been added. Please enable service.
Adil
01-14-2014 01:27 PM
HI Adil,
I guess #wccp version 2.
Regards,
Kanwal
01-14-2014 01:31 PM
No, it doesn't accept this command.
cdrwaas01(config)#wccp version 2
^
% Invalid input detected at '^' marker
01-15-2014 04:27 AM
Hi Adil,
Just configure :
waas01(config)#wccp tcp-promiscuous service-pair 61 62 enable
... and you will (hopefully) get a message stating that you have successfully enables the service.
Best Regards
Finn
01-15-2014 06:29 AM
I think the command it was expecting is "cms enable".
01-15-2014 06:42 AM
Hi Adil,
"cms enable" registers the WAAS accellerator at the Central manager, so you can configure the WAAS from the CM ... if you prefer a GUI.
... and from there you can setup the WCCP, by clicking around ;-)
And there is probably a checkmark for the enabling of the service :
but what it does is basically sends out the commend to the remote WAAS, you can verify it in the config.
Best regards
Finn
01-19-2014 07:03 PM
this same problem when im deploy waas,
after enable tcp prosmiscuous, it will move from global-config to whatever mode im forget-im sorry.
after you moved to another global-config just type "enable"
edit : see this link
see in the section of enable of WCCP service..
just hit "enable" voilaa..your wccp service turn on.
regards,
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: